KitchenAid KUDE70FVPA, KUDE60FVPA Install Custom Panel Option, Mark line, Mark pilot holes, Back

Page 15

Install Custom Panel – Option 1

(Models KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of the custom panel, the screw holes should be countersunk for the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed the panel thickness. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

NOTE: A customer-supplied full front panel must weigh no more than 16 lbs (7.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the custom panel because of the precise dimensions needed.

NOTE: All mounting hardware supplied is for a 3/4"

(19.1 mm) thick wood panel. If a thinner wood panel, or materials other than wood are used, it is the consumer’s responsibility to obtain the proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture resistant sealer on both sides and all edges of the panel to avoid damage from humidity.

1 Custom panel installation - Dishwashers with control panel on the top

23 1/2”

 

 

*30 3/16” (76.7 cm)

(59.7 cm)

 

 

 

3/4” (19.1 mm)

*This dimension is for 4” (10.2 cm) toe kick. If the installation needs a higher toe kick, adjust the height of the wood panel accordingly. Not recommended for toe kicks greater than 6” (15.2 cm).

With a TORX® screwdriver, remove three screws from both sides, as shown; hold the outer panel up while removing the screws. Save screws for reinstallation.

2 Dishwashers with control panel on top custom panel dimensions

3 screws per side

outer panel

Gently set outer panel aside. Lay the customer-supplied custom panel face down on a covered, non-scratching surface.

3 Mark line

9 29/32”

(25.2 cm)

Back

Top edge

Measure 9 29/32" (25.2 cm) from top edge and mark a line on the back of customer-supplied custom panel. Position the outer panel on the back of the customer-supplied custom panel as shown, so that the top holes in the outer panel are on the line, and both panels are centered side to side.

4 Mark pilot holes

Mark pilot

holes

Mark all four hole locations; remove outer panel. Drill 3/32" pilot holes 1/2" (13 mm) deep in customer-supplied custom panel. Place the outer panel on the back of the customer- supplied custom panel; align holes.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents W10056407A You Need to Table of ContentsParts supplied Tools and PartsTools needed Other useful items you may needLocation Requirements 60 /8 Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose Waste disposer with air gap Install Moisture Barrier on some modelsInstall moisture barrier on some models No waste disposer no air gapPrepare Dishwasher Power Cord-Connect remaining wires Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Supply Cord- Connect ground wireDetermine Cabinet Opening Built-up Floors-Add shims as needed Install the Door Handle on some modelsCustom Panel Dimensions Install door handleModels KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, and KUDE70FVPA Install Custom Panel OptionMark line Mark pilot holesModels KUDC03IV and KUDS30IV Install custom panelAttach handle Attach body panelOption 1, Countertop attachment Choose Attachment OptionCountertop attachment Remove brackets from the topMove Dishwasher into Cabinet Opening Door falls open Increase spring tension Check water and drain hose positionOpen and close door Closes too quickly Decrease spring tensionConnect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire--Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in strain reliefSecure Dishwasher in Cabinet Opening Complete Installation If Dishwasher Does Not Operate Power supply cord-Plug into a grounded 3 prong outletReconnect power Check OperationPage Il faut Table des matièresOutillage et pièces Exigences demplacement Enlev Utilisation du dispositif de brise-siphon Exigences dévacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de connexion lutilisateur emploie-t-il? Déconnexion de lalimentation électriqueFermeture de lalimentation en eau Lutilisateur possède-t-il déjà des moyens de raccordement?Raccordement direct Préparation du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Perçage du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Application de ruban adhésif Téflon ou composé détanchéité Préparation du lave-vaissellePlacer le lave-vaisselle sur le dos Dépose des panneauxRaccordement du cordon dalimentation Installation dun serre-câbleTableau de réglage de la hauteur du lave-vaisselle Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Mesure de louverture dencastrement du placardPlanchers surélevés Ajouter des cales si nécessaire Installation de la poignée de porte sur certains modèlesDimensions du panneau personnalisé Installation de la poignée de porteModèles KUDS40FVPA, KUDS50FVPA, KUDE60FVPA, et KUDE70FVPA Installation du panneau personnalisé OptionMarquage de laxe Marquage des avant-trousModèles KUDC031V et KUDS301V Installation du panneau personnaliséFixation de la poignée Fixation du panneau principalOption 1, Fixation au plan de travail Choix de l’option de fixationFixation au plan de travail Dépose des brides du dessusInsertion des boutons en plastique Réinstallation de la brideDéplacement du lave-vaisselle à proximité de louverture Sectionnement de lextrémité de la brideInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteEnfiler lécrou et la virole sur la canalisation Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Vérification de laplomb et réglage des pieds si nécessairePosition définitive de la bride de tuyau Raccordement au circuit dévacuationEnfilement de la bride sur le raccord Recherche de fuitesRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Achever linstallation Rétablir l’alimentation électrique Inspection de la rive de panneau inférieureSerrage des vis Reconnexion de lalimentation électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementConseils supplémentaires 12/08
Related manuals
Manual 56 pages 6.48 Kb

W10056407A, KUDS40FVPA, KUDS50FVPA, KUDE70FVPA, KUDE60FVPA specifications

The KitchenAid W10056407A and its associated dishwasher models, including KUDE60FVPA, KUDS40FVPA, KUDS50FVPA, and KUDE70FVPA, represent a blend of innovation, efficiency, and elegant design in today’s modern kitchen appliances. These models are designed to provide exceptional cleaning power while being user-friendly.

One of the standout features of these dishwashers is their Advanced Clean Water Wash System, which uses a combination of powerful jets and filtration to ensure that every dish is cleaned thoroughly, even the dirtiest pots and pans. This technology minimizes the need for pre-rinsing, saving both time and water. The Efficient Wash Cycle allows users to customize the cleaning according to their needs, providing options for heavy-duty washing or light cycles for delicate items.

Another remarkable feature is the ProWash Cycle, which automatically determines the optimal cycle for the load being washed. This technology analyzes soil level and adjusts the wash time and water usage accordingly, making it a smart choice for those who want to conserve resources without sacrificing cleaning results. Additionally, the models boast a Quiet Operation, with advanced sound insulation technology that ensures a near-silent experience, allowing users to carry on with other activities without being disturbed by noise from the dishwasher.

The adjustable racks in models like the KUDE70FVPA make loading and unloading a breeze. The upper rack can be adjusted to accommodate taller items without compromising space in the lower rack, enhancing the overall capacity of the dishwasher. Furthermore, the complete stainless-steel interior not only adds to the durability of the appliance but also contributes to better drying performance, as it helps retain heat during the drying cycle.

These KitchenAid dishwashers also come equipped with a high-efficiency spray arm that ensures even water distribution, reaching every corner for a comprehensive clean. The sleek design and innovative features make these models not only functional but also aesthetically pleasing, complementing any modern kitchen decor.

In terms of energy efficiency, these appliances are Energy Star certified, confirming they use less energy and water without sacrificing performance. This commitment to environmental sustainability reflects KitchenAid's dedication to quality and responsibility, making these models an excellent choice for eco-conscious consumers. Overall, the W10056407A, KUDE60FVPA, KUDS40FVPA, KUDS50FVPA, and KUDE70FVPA dishwashers provide a perfect blend of performance, convenience, and style.
Top Page Image Contents