KitchenAid W10078153B Choose attachment option, Check door spring tension

Page 15

Choose attachment option

WARNING

Excessive Weight Hazard

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

Using two or more people, stand the dishwasher up.

4.Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher is installed.

plastic button

5. Push bracket into slot on the side of dishwasher, and

bend tab in towards the side of the dishwasher so that it

Option 1: Countertop attachment

The dishwasher must be secured to the cabinet. There are two brackets on top of the dishwasher that can be attached to the countertop if it is wood, laminate or other similar surfaces. If your countertop is marble, granite or other hard surface the brackets may be moved to the sides of the dishwasher.

brackets

front vent

model shown

keeps the bracket in place. Repeat this step for the other

side of the dishwasher.

NOTE: Do not attach the dishwasher, this will be done

later.

bend tabs

NOTE: Do not attach the dishwasher, this will be done later.

Option 2: Dishwasher side attachment

(for marble, granite or other hard surface countertop)

1.To remove the brackets from the top, flatten tab at back of brackets with pliers, and pull the brackets out of the slots.

tabs

2.Break off the end of the bracket along the scored line.

score line

3.With another person holding the rear of the dishwasher to keep it from tipping, open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will keep screws from falling into pump area when securing dishwasher to cabinet.

Check door spring tension

1.With another person holding the rear of the dishwasher to keep it from tipping, open and close the door a few times. If the door closes or falls open under its own weight, the door tension will need to be adjusted.

2.To adjust the door spring tension, unhook the spring from the rear leg of dishwasher.

3.With a 5/16" nut driver or hex socket, remove the screw from the tensioner.

4. The screw can be put into one of three holes , , in the front leg of dishwasher. If the door closes by itself, move the tensioner to a higher number hole and replace screw. When door is unlatched, if it opens by itself, move tensioner to a lower numbered hole and replace screw.

5.Re-attach door spring to rear leg. Tensioners on both sides of dishwasher should be secured at same holes.

spring

tensioner

screw

15

Image 15
Contents Home Appliances Dishwasher Safety Table of ContentsYou need to Tools and Parts Installation RequirementsAll installations Addition, for new installationsCutout dimensions Product dimensionsWater Supply Requirements If direct wiring dishwasherIf connecting dishwasher with a power supply cord Drain RequirementsOption 1 Waste disposer with air gap Installation InstructionsPrepare cabinet opening using existing utility hookups Install the drain hoseOption 4 No waste disposer no air gap Option1 Direct wire methodElectrical connection Option 2 No waste disposer with air gapOption 2 Power supply cord method Install the water lineInstall moisture barrier on some models If you have built-up floors Prepare dishwasherInstall the door handle on some models Install the door handle-Pro Line seriesInstall door panel-Pro Line series For dishwashers with the control panel shown below Custom panel dimensionsOption 1 For models KUDS03FTPA and KUDU03FTPA Install custom panelOption 2 For models KUDC03IT, KUDK03IT and KUDL03IT Option 2 Dishwasher side attachment Choose attachment optionCheck door spring tension Option 1 Countertop attachmentLevel the dishwasher Option 1 Direct wire methodMake Electrical Connection Move dishwasher into cabinet openingConnect to water supply Secure dishwasher in cabinet opening Connect to drainComplete installation Bottom sound pad installation on some modelsIf dishwasher does not operate Check operationSécurité du lave-vaisselle Table des matièresTenir compte de ceci Outillage et pièces Exigences d’installationEmplacement d’installation Pour toutes les configurations d’installationDimensions de l’espace d’installation Dimensions du produitPour le raccordement direct du lave-vaisselle Spécifications de la canalisation d’évacuationSpécifications de l’alimentation en eau Spécifications électriquesInstructions d’installation Installation du tuyau d’évacuationOption 1 broyeur à déchets avec brise-siphon Raccordement électrique Préparation de l’emplacementInstallation de la canalisation d’eau Option 2 raccordement par cordon d’alimentationImportant Utiliser toujours un tuyau d’évacuation neuf Installation de la barrière contre lhumidité Préparation du lave-vaisselle Installation de la poignée de porte Installation du panneau de la porte- série Pro LineLine Dimensions du panneau de porte personnalisé Dimensions du panneau personnaliséOption 1 Pour les modèles KUDS03FTPA and KUDU03FTPA Installation du panneau personnaliséOption 2 Pour les modèles KUDC03IT, KUDK03IT, KUDL03IT Option 1 Fixation sur le plan de travail Choix de la méthode d’immobilisation de l’appareilPlacer délicatement le panneau externe à part Placer le panneau personnalisé fourni par le client faceInsertion du lave-vaisselle dans l’espace d’installation Contrôle de la tension des ressorts de la porteÉtablissement de l’aplomb du lave-vaisselle Raccordement électrique Option 1 Câblage directConseil utile Raccordement à la canalisation d’évacuation Raccordement à la canalisation d’eauInstallation du panneau d’insonorisation Alimentation de l’appareil par câblage direct Dernières opérations de l’installationContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementW10078153B