Whirlpool RH9330XL Electrical Grounding, Free Standing Wall Installation, For Wall Venting

INSTALLATION IJNDEQ KITCHEN F’JFQ ‘I)O’i’!Y

1.For easy, one man I-staliation hood should be disassembled.

First, remove the aluminum filter from fan box assembly by pulling tab toward opposite end of filter.

Remove two mount ng screws fcund in fan box near back. (Figure :.)

Unplug power supply cord connection near back.

Remove additional four screws from fan box assembly and lift assembly out.

iisrnode tour scret.cs nolcrng top to canopy assem biy

2.Fa3R TOP VENTING:(Figures 2, 7 8 8)

Using the canopy ?oo as a hole !ocating pattern,

make a 7’/4” diameter hole. If the optional

rectangular

transition

is

to be

used,

make a

3’b”xlO’;;”

rectz:.juirar

hole.

Mark

an-

c*:

,.;;e

for

wrring.Flanged

hole

is

provided

in

canopy

for

wiring

entrance

FOR

WALL

VENTING:

(Figures

2 & 9)

Establish

center

line

for

the

hole

pattern

by

measur’ng

half

the

width

of

the

canopy

and

10%” from the

top

of

the

canopy.

Make

a

7%”

diameter

hole

through

the

wall.

Mark and

cut

hole

for

wlrlng

F!anged

hole

is

provided

in

canopy

top

for

wiring

entrant

FCP

DUCTLfSS

, INSTALLATION:

Refer

to

InstructIons

found

in ductless

kit

RCH

9600

for

remarnrng

installation

procedure.

3.Install canopy top to kitchen furr down with four

screws provided in installation pack, Fig. 5.

4.Install canopy assembly by sliding top flanges

of canopy assembly onto mating flanges on canopy top, Figure 5. Secure with 4 screws prevrously removed.

5.Make electrical connection at wiring box on back of canopy assembly according to Figures 3&6

6.With necessary duct work in place (see Fig. 4), lift fan box assembly into position and secure with 6 screws.

7.Plug hood power supply into receptacle.

8.Replace filter.

FREE STANDING WALL INSTALLATION:

1.For easy, one man Installation, hood should be :+sassnm5ls<

First, remove the aluminum tilter from tne fan box assembly by pulling tab toward opposite

end of filter. Remove two mounting screws found in fan box near back. (Figure 1)

Unplug power supply cord connection near

back Remove additional four screws from fan box assembly and lift assembly out.

i?. I- *I y,pTr“,, “C’T-!hli, ,ap.-J mark lorytion for 2

:r;OainiI:-.gno,55 dt r ii;’ c: <(t-y I1oie -,3is. i,i!;Jre

4)

3.Insert screws Into n-arkea location leaving l/l6 to l/8 inch between wall and screw head. NOTE:lf hollow sheetrock wall IS encountered, molly bolts should be used instead of those

provided In installation packet. AddItional support should be provided after canopy is in place, when hollow wall molly bolts are used.

4. Hang hood on mounting screws and mark location for venting and wiring. Remove canopy to cut holes.

FOR TOP VENTING: Mark venting hole

locations through the ceiling or other

obstructions between hood top and attic. Cut a 7’6” diameter hole for round venting (Fig. 7) or

a 3;;” x 10’,q” h~,e for rectanglr,a-,,~nili:g, Fig. 8.

FOR WALL VENTING:	Establish	the	center for
the back vent hole bv measurina		half	the width

of the hood and down 1 O-1/4” from canopy top. See Figures 2 and 9.

FOR DUCTLESS		INSTALLATION:	Refer	to
instructions	found	in ductless kit RCH	9600	for
remaining	installation	procedure.

5.Replace hood and tighten screws

6.Make electrical connection at wiring at box on

back of canopy according to Figures 3 & 6.

7.Witn nec?ssar:/ duct tn place (see Figure 4; ‘*rt fan box assembly into posrtion and secure >,*ylth

six screws.

8.Plug hood power supply into receptacle.

9.Replace filter.

FUAR DOWN ~-	-~ HOLE PATTERN	FOR
	TOP VENTING	ONLY
	F
CANOPY	TOP ~-\

DOORS	~
	7;‘TO	7;‘lNCH		DIA	CENTER	LINE
	HOLE	FOR	BACK		OF HOOD
	VENTING	ONLY		FIGURE	2
		7”	ROUND	DUCT
					KEYHOLE
					MOUNTING
					HOLE
					HOOD
					WIRING
				--4	‘-1”	WIDE
1				LIZ	FLANGE		ON
					HOOD		BACK
		FIGURE		3

ELECTRICAL GROUNDING:

Permanently ground this unit in accordance with the latest National Electrical Code and applicable

local codes and ordrnances. It is recommended that

a permanent ground connection be made to the untt

using a conductor of appropriate size from a

grounded continuous metalltc cold water pipe, a

grounded lead in the service panel or a properly

driven and electrically grounded ground rod. Do not ground to a gas supply pipe.

Page 2