Hotpoint DX 892 CX manual Installation

Page 5

Installation

Electrical Requirements

GB For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than 130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed in the manner illustrated i.e. having side, back, and roof panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3. Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Build-in Electric double oven Contents Instructions for Installation and UseIntroduction To the InstallerTo the User Retention of this Instruction BookSafetyInformation Never AlwaysInstallation Tall Cabinet Ventilation 595mm Overall view Control panel Main parts of your DoubleOvenDisplay KnobSetting the minute minder Setting the clockStart-upanduse Control panel lockResidual heat indicators Restoring the factory settingsStandby Cooling ventilationAutomatic cooking modes Manual cooking modesRoast Meat mode Fish modeSetting the end time for a cooking mode Practical cooking adviceProgramming cooking Programming the cooking durationThis will cause overheating SolarplusGrillUsing the grill pan kit Platewarming in the top oven To use the oven proceed as followsDo not place food or dishes on the floor Oven.GB TopOvenTemperature Charts-Meat TopOvenTemperature Charts-Baking Telescopic runners and Meat pan Cooking temperature rangesMainOven-TheIntelligentCooking System Cooking Advice TableTemperatureConversionChart How Stayclean works Care and CleaningCleaning Base & Rear of Top Oven and Base of Main OvenInner Door Panels & Glass Control PanelRefit the door inner glass as follows Remove the door inner glass as followsGB There MAY be Nothing Wrong If something Goes wrongDisposal of old electrical appliances Disposal of your productGuarantee is subject to the following conditions Months Parts and Labour GuaranteeGuarantee does not cover Year Parts GuaranteeUK 08448 24 24 Republic of Ireland 01 230 Hotpoint ServiceParts & Accessories

DX 892 CX specifications

The Hotpoint DX 892 CX is a versatile and innovative dishwasher designed to simplify your daily cleaning tasks while delivering exceptional performance and efficiency. Aimed at modern households, it combines advanced features with a sleek design, making it a great addition to any kitchen.

One of the standout features of the Hotpoint DX 892 CX is its generous capacity. With the ability to accommodate up to 16 place settings, this dishwasher is perfect for families or those who frequently entertain guests. The spacious interior allows for the placement of larger items, such as pots and pans, without compromising on cleaning power.

Equipped with several wash programs, the DX 892 CX ensures that your dishes are treated according to their specific needs. The different settings include intensive cleaning for heavily soiled pots and a delicate cycle for fragile glassware, providing flexibility for all types of dishwashing requirements. The Eco option is particularly notable, as it maximizes water and energy efficiency, helping you save on utility bills while being environmentally friendly.

One of the key technologies featured in the Hotpoint DX 892 CX is the 3D Zone Wash, which allows for a more targeted cleaning performance. This system provides adjustable cleaning zones, enabling users to customize water pressure according to the load, ensuring that tough stains are eliminated while offering gentler care for delicate items.

The dishwasher also boasts a Quiet Motor technology, making it one of the quieter options on the market. With a noise level of just 44 dB, you can run your dishwasher without disrupting the peace of your home. Additionally, the Active Drying system uses residual heat to enhance the drying process, resulting in spotless and shine-dry dishes every time.

In terms of energy efficiency, the Hotpoint DX 892 CX scores highly, typically rated at A+++. This means reduced energy consumption without sacrificing performance, a critical aspect in today’s eco-conscious living.

Furthermore, the appliance features a sleek stainless-steel finish, providing a modern and stylish look to complement your kitchen décor. Its user-friendly interface includes an easy-to-read display and intuitive controls, making it accessible even for those who may not be tech-savvy.

In summary, the Hotpoint DX 892 CX is a feature-rich dishwasher that combines innovative technologies with practicality. With a vast capacity, customizable wash settings, and a commitment to energy efficiency, it stands out as an excellent choice for anyone looking to enhance their kitchen functionality.
Top Page Image Contents