Denon AVR-1802/882 manual Use left and right buttons to set the D. COMP. Initial

Page 34

ENGLISH

SURROUND

MENU

(Remote control unit)

Press SURROUND or (down) button to switch to the D.COMP. setting.

5

(Remote control unit)

SURROUND

MENU

(Remote control unit)

Use (left) and (right) buttons to set the D. COMP. (Initial)

 

 

 

 

OFF

 

 

LOW

 

 

 

MID

 

HIGH

 

 

D.COMP. OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(left) button

 

 

 

(right) button

 

 

 

 

 

 

 

Press SURROUND or

(down) button to switch to the LFE setting.

NOTE:

 

 

 

This

parameter is not displayed

 

 

 

 

 

 

 

 

 

during DTS playback.

6

(Remote control unit)

SURROUND

MENU

(Remote control unit)

Use (left) and (right) buttons to set the LFE level.

LFE 0dB

•The level can be adjusted in units of 1 dB from –10 to 0 dB.

Set to the desired level according to the speaker systems being used and the source to be played.

Press SURROUND or (down) button to switch to the default setting.

7

To reset the settings to the factory defaults, use

(left) and

(right) buttons to display “Yes”.

 

(Remote control unit)

DEFAULT Y/N

YES

NO

SURROUND

MENU

(left) button

(right) button

Press SURROUND or (down) button to switch to the CINEMA EQ. setting.

(Remote control unit)

NOTE:

•When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and the setting will be completed.

Surround parameters w

CINEMA EQ. (Cinema Equalizer):

The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture soundtracks. Select this function if the sound from the front speakers is too bright.

This function only works in the Dolby Pro Logic, Dolby Digital and DTS Surround modes.

D.COMP. (Dynamic Range Compression):

Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at night, or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital.) Select one of the four parameters (“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.

LFE (Low Frequency Effect):

Program source and adjustment range

1.Dolby Digital: –10 dB to 0 dB

2.DTS Surround: –10 dB to 0 dB

When Dolby Digital encoded software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct Dolby Digital playback.

When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct DTS playback. When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to -10 dB for correct DTS playback.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents AVR-1802/882 Nous vous remercions pour l’achat de cet appareilEnglish Francais Safety Instructions Table of Contents Before UsingFeatures Part Names and Functions Front PanelRemote control unit System System SET UPFinally, setting up the system Setting UP the Speaker SystemsRead this First Line Line OUT Connecting the audio componentsConnections Front Subwoofer Center Surround Line OUTConnecting the video equipments Connecting a video decks Connecting a TV/DBS tunerConnecting a DVD player or a video disc player VDP Connecting the audio output jacksConnecting a monitor TV Connecting a video component equipped with S-video jacksPrecaution when using S-jacks Connecting the video decksAM loop antenna assembly Connection of AM antennas Connecting the antenna terminalsFM antenna adapter assembly Precautions when connecting speakers Connecting the speaker cordsConnecting banana plugs Speaker system connectionsProtector circuit Range of operation of the remote control unit Using the Remote Control UnitInserting the batteries System Setup button Setting UP the SystemUse the following buttons to set up the system Cursor buttons , ª, 0Setting the speaker configuration Before setting up the systemPress the System button to enter the setting Subwoofer mode Setting the Subwoofer ModeAssignment of low frequency signal range ParametersPreparations Setting the delay timeListening position After setting up the system Digital input setupTerminal Operating Denon audio components Remote Control UnitPreset memory Audio component For tape deck TapePreset memory Video component For video disc player VDP Operating a video component stored in the preset memoryFor DVD player For video deck VCROperation Check that all connections are proper Turn on the powerRemote control unit to turn on the power Before operatingInput mode selection function To select the input mode from main unitTo select the input mode from the remote control unit Playing the input sourceDolby Digital Adjusting the sound quality toneAfter starting playback DTSTurning the sound off temporarily muting Listening over headphonesChecking the currently playing program source, etc Playback using the external input EXT. in jacks Mode AUTO, PCM, DTS or Analog button to switch toBefore playing with the surround function Adjust the level of the selected speakerSurround Digital or DTS modesDolby Surround Pro Logic II mode Dolby PRO LogicDimension setting Cinema EQ settingPanorama setting Center Width settingPosition of the slide switch on Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode Remote control unitSurround parameters w Cinema EQ. Cinema Equalizer Use left and right buttons to set the D. COMP. InitialUse left and right buttons to set the LFE level COMP. Dynamic Range CompressionVideo Game Surround modes and their featuresDSP Surround Simulation Personal Memory PlusUse Left Right buttons to set the room size Initial DSP surround simulationUse Left Right buttons to set the effect level Initial Delay 30ms Use Left Right buttons to set the delay time InitialWhen turned counterclockwise When turned clockwisePress Surround Parameter Surround parameters e Surround modes and parametersAuto preset memory Listening to the RadioManual tuning Auto tuningPress Tuner to set the input function to Tuner Preset stations Recalling preset stationsLast Function Memory Initialization of the MicroprocessorAdditional Information Speaker setting examplesSurround Dolby Digital compatible media and playback methods Dolby Digital and Dolby Pro LogicDolby Pro Logic DTS Digital Surround DTS compatible media and playback methodsTroubleshooting Specifications Avant de mettre sous tension Table DES MatieresAvant L‘UTILISATION Ranger ces instructions dans un endroit sûrPrecautions DE Manipulation Precautions D’INSTALLATIONCaracteristiques Nomenclature ET Fonctions Panneau avantUnité de télécommande System SET UPLire EN Premier Ensuite, insérer les piles dans la télécommandeFinalement, configurer le système Réglage DES Systèmes D’ENCEINTEMettre cet appareil sous tension. Dans ce cas, mettre cet ConnexionsConnexion des composants audio Audio. Ne pas les utiliser pour un sèche-cheveux, etcPrises numériques Digital Connexion des composants vidéoConnexion d’un lecteur de CD Connexion d’un jeu vidéoPlatine vidéo Connexion d’un téléviseur/tuner DBS Téléviseur/DBSPrise de sortie de moniteur Monitor Connexion des lecteurs vidéoRemarque à propos des prises en S Connexion d’un composant vidéo équipé de prises vidéo SPrécautions d’utilisation des prises en S Remarques Remarque à l’installateur de système de télédistributionConnexion des bornes d’antennes Ensemble d’antenne-cadre AM Connexion des antennes AMConnexions du système d’enceintes Connexion des bornes d’enceinteCircuit de protection Plage d’utilisation de la télécommande Utilisation DE LA TélécommandeInsertion des piles Touches Cursor , ª, 0 Installation DU SystemeTouche System Setup Touche SelectAppuyer sur la touche System pour accéder aux réglages Avant de configurer le systèmeConfiguration des haut-parleurs Touche gauchePrécaution Réglage de la sortie de graves Subwoofer ModeParamètres Utiliser les touches gauche Et droitReglage de la temps de retard PréparationsOptique 2 OPT Initial Configuration de l’entrée numériqueApres avoir configure le système PHONO, Tuner et V. AUX ne peuvent pas être sélectionnésMémoire préréglée Composants audio Unite DE TelecommandeUtilisation des composants audio Denon Pour platine cassette TapeMémoire préréglée Composants vidéo Pour platine vidéo VCR Pour lecteur DVDPour lecteur de vidéodisque VDP Pour moniteur de téléviseurAvant l’utilisation PréparatifsLecture de la source de programme analogique Réglage de la qualité sonore tonalité Après le début de la lectureRéglé est sélectionné, tourner le bouton Muting Ecoute avec casqueDésactivation provisoire du son sourdine Video SelectPour choisir le mode d’entrée souhaîté. Voir Annulation du mode d’ entrée externeSur le bouton Input Mode AUTO, PCM, DTS ou Analog Lecture en utilisant les prises d’entrée externe EXT.Tone AmbianceAvant la lecture utilisant la fonction d’ambiance Ajuster le niveau de l’enceinte sélectionnéeMode Dolby Surround Pro Logic ExempleParamètres d’ambiance q Mode Pro Logic Réglage DimensionRéglage Default Mode PanoramaGlissière de la télécommande est en Régler le mode d’entrée à Auto ou DTSSélectionner le mode Dolby/DTS Surround Sélectionner la source d’entréeCOMP. Compression de gamme dynamique Paramètres d’ambiance w Cinema EQ. Eqaliseur CinémaLFE Effet de basse fréquence Modes d’ambiance et leurs caractéristiques Simulation D’AMBIANCE DSPMémoire personnelle Plus Simulation d’ambiance DSP Touche gauche Touche droitDefault Y/N Lorsqu’il est tourné dans le sens anti-horaire Lorsqu’il est tourné dans le sens horaireAppuyer sur la touche Surround Parameter Efect Level Niveau d’effet Delay Time Temps de retardParamètres d’ambiance e Room Size Taille de piece Modes d’ambiance et paramètresEcouter DE LA Radio Mémoire préréglée automatiqueSyntonisation manuelle Syntonisation automatiqueRégler la fonction d’entrée à Tuner Rappel de stations préréglées Stations prérégléeStocker la station dans la mémoire préréglée Memoire DE Derniere Fonction Initialisation DU MicroprocesseurAmbiance Informations SupplementairesRéglage de base Dolby Digital et Dolby Pro Logic Méthodes de lecture et média compatibles Dolby DigitalMéthodes de lecture et média compatibles DTS Depistage DES Pannes RemarqueTélécommande RC-897 Piles Rapport signal/bruitConsommation Dimensions externes maximales Dimensions externesVDP List of Preset Codes / Liste DE Codes Préréglés DVDVCR Francias English 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan

AVR-1802/882 specifications

The Denon AVR-1802 and AVR-882 are notable models in Denon's lineup of audio/video receivers, catering to home theater enthusiasts who demand quality sound and versatility. These receivers, popular in the early 2000s, combine advanced technologies with user-friendly features to deliver an immersive audio experience.

One of the standout features of the Denon AVR-1802 is its high-power output, capable of delivering 80 watts per channel across seven channels. This allows it to effectively drive a full home theater speaker setup, ensuring that every sound, from the subtlest whispers to the most explosive action sequences, is rendered with clarity and depth. The receiver supports both Dolby Digital and DTS decoding, allowing users to enjoy a wide array of movie soundtracks with impressive fidelity.

The AVR-882, while slightly more advanced, shares similar audio capabilities and adds features like multi-room audio support and enhanced connectivity options. It includes multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players and gaming consoles without the hassle of constantly switching cables. The ability to process high-definition audio formats makes both receivers compatible with modern home theater setups.

In terms of processing power, both models utilize Denon’s proprietary processing technology, which enhances audio clarity and improves the overall listening experience. The inclusion of Advanced AL24 Processing ensures that digital audio is upsampled effectively, maintaining the integrity of sound as it passes through various stages.

Another commendable characteristic is the intuitive user interface and setup process. Denon has designed these receivers with ease of use in mind, featuring an on-screen display that simplifies the navigation of numerous settings. The presence of automatic speaker setup technology, often referred to as EQ calibration, allows users to optimize audio performance based on the unique acoustics of their room.

Connectivity options are robust as well, with numerous analog and digital inputs, including composite, component, and S/PDIF connections for versatile compatibility with older and newer devices, making these receivers suitable for a variety of setups.

Overall, the Denon AVR-1802 and AVR-882 exemplify the blend of power, technology, and convenience that Denon aims to offer, promising both casual listeners and serious audiophiles a quality audio experience that stands the test of time. Their features not only enhance home theater configurations but also ensure vibrant audio playback for music and movies alike, making them valuable additions for anyone looking to elevate their entertainment experience.
Top Page Image Contents