Wells 1222 1222CA Temperature Adjustment, Remove Tank LID Assembly, Replace Thermostat

Page 12

SERVICING INSTRUCTIONS (continued)

TEMPERATURE ADJUSTMENT

Check temperature at discharge of faucet.

Remove thermostat access button plug to access thermostat. Turn thermostat shaft clockwise to increase temperature.

REMOVE TANK LID ASSEMBLY

Unplug dispenser or turn circuit breaker OFF. Turn OFF water supply. Remove rear panel.

Disconnect fill tube and vent tube from tank lid. Disconnect wiring from hi-limit, thermostat and heating element as necessary. Remove eight lid screws Remove lid assembly by lifting it straight up.

Reassemble in reverse order.

REPLACE THERMOSTAT

Unplug dispenser. Remove back panel.

Loosen and free jam nut from pass-thru fitting securing thermobulb. Lift out probe, jamb nut and gasket. Disconnect wiring from thermostat. Loosen screws holding thermostat to bracket. Remove thermostat.

Reassemble in reverse order.

IMPORTANT:

The thermostat will maintain temperature within ±3ºF. For high altitude locations, thermostat should be adjusted to a maximum temperature equal to the local boiling temperature minus 5º. This will prevent boiling water in the dispenser,

NOTE:

Thermostat is adjustable to a maximum of 199ºF.

IMPORTANT:

Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line.

IMPORTANT:

Before setting lid assembly into tank, make sure tank lid gasket is properly seated on flange of lid.

712 76580 Owners Manual Hot Water Dispenser

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 712 Warranty Statement Table of Contents SpecificationsApplicability Features and Operating Controls Precautions and General Information Agency Listing InformationEquipment Damage Burn HazardInstallation PLUMBER’S Installation InstructionsUnstable Equipment Hazard Refer to Exploded Views page 14 for Component NAMES/NUMBERSELECTRICIAN’S Installation Instructions Shock HazardOperation Water HeaterWater Level START-UPCleaning Instructions FrequencyTools Troubleshooting Suggestions Symptom Possible Cause Suggested RemedyAccess Panels Servicing InstructionsRear Panel Solenoid DoorTemperature Adjustment Remove Tank LID AssemblyReplace Thermostat Replace Heating Element Replace SolenoidRepair HOT Water Faucet Procedure Delime the Water Tank Chemical Burn HazardExploded Views and Parts Lists Service KitsFaucet Repair Kits Solenoid Repair Kits19 2 Reqd Description Model 1222 and 1222CA Wiring Diagram Genuin e Parts

1222 1222CA specifications

Wells 1222 1222CA represents a significant advancement in the realm of wastewater management and treatment solutions. Designed for both commercial and residential applications, this model epitomizes efficiency and reliability. It is engineered to meet the growing demand for sustainable practices in water management, addressing the complexities of wastewater through innovative technologies.

One of the hallmark features of the Wells 1222 1222CA is its advanced filtration system. The model employs a multi-stage filtration process, incorporating both mechanical and biological filtration to ensure that wastewater is treated thoroughly. The mechanical aspect utilizes fine mesh screens to capture larger particles and debris while the biological component promotes the growth of beneficial bacteria that help break down organic matter. This two-tier approach enables superior effluent quality, significantly reducing the potential for pollutants entering local water bodies.

In addition to its filtration capabilities, the Wells 1222 1222CA model includes state-of-the-art sensor technology. These sensors monitor parameters such as water levels, flow rates, and overall system performance. This real-time data collection allows for proactive maintenance and ensures that the system operates within optimal parameters. The integration of smart technology also facilitates remote monitoring and control, providing users with the ability to manage the system via a mobile application, adding convenience and enhancing operational efficiency.

The construction of the Wells 1222 1222CA is robust, utilizing high-quality, corrosion-resistant materials that ensure durability and longevity. This model is designed to withstand varying environmental conditions, making it suitable for diverse geographic locations. Furthermore, its compact size allows for easy installation in limited spaces, accommodating the needs of urban environments.

Another notable characteristic of the Wells 1222 1222CA is its energy-efficient design. By employing energy-saving technologies, the system minimizes its carbon footprint while still delivering optimal performance. This focus on sustainability is complemented by a user-friendly interface that simplifies operation for all users, ensuring that both novice and experienced operators can manage the system effectively.

Overall, the Wells 1222 1222CA offers an innovative solution for wastewater treatment, combining advanced filtration, smart technology, durable construction, and energy efficiency into one cohesive unit. This model not only meets regulatory standards but also promotes environmental stewardship, making it an invaluable asset for those dedicated to responsible water management practices.
Top Page Image Contents