Frymaster none Replacing the Temperature Probe or High Limit Thermostat, Replacing the Air Heater

Page 5

HEATED PASS THROUGH

INSTALLATION, OPERATION, SERVICE, AND PARTS

6.2Replacing the Temperature Probe or High Limit Thermostat

A.Disconnect the unit from the electrical power source.

B.Turn the unit on its side. Remove the five screws from the chassis bottom.

C.Set the unit down on its base.

D.Carefully lift the cowl assembly upward until it is clear of the blower assembly, then lay it on the table behind unit.

E.The air tower has two sections – a removable front section and the fixed rear section. The front section must be removed to access the temperature probe and high limit thermostat. A pair of slotted brackets, one at each end, holds the front section in place. Insert a 516-inch nut driver through the air outlet opening and turn the nuts on the outside studs counterclockwise to loosen them. Do not remove the nuts.

F.Grasp the bottom flange of the tower and push upward while rotating the bottom outward to disengage the two slotted brackets on the front section from the studs on the rear section.

G.Cut the leads of the failed component near the component.

H.If replacing the temperature probe, unplug the probe connector from the controller board., but leave the leads in place for now.

I.Remove the failed component from its mounting and install the replacement component in its place.

J.Securely connect the leads from the new component to the old leads cut in Step G on the air tower side of the unit. Grasp the old leads at the opposite end and gently pull them through the unit. NOTE: It is easier to pull one lead through at a time.

If the leads become disconnected while pulling them through, it will be necessary to remove the plate. Refer to Steps G through J in procedure 6.3 below.

K.Once the new wires have been pulled through, replace the terminals cut off in Step J.

L.If replacing the temperature probe, use a pin pusher to disconnect the old leads from the plug and connect the new wires. Reconnect the plug to the controller board.

M.If replacing the high limit, connect the leads as shown in the wiring diagram (polarity does not matter).

N.Reassemble the unit by reversing Steps A through F.

6.3Replacing the Air Heater

A.Disconnect the unit from the electrical power source.

B.Turn the unit on its side. Remove the five screws from the chassis bottom.

C.Set the unit down on its base.

D.Carefully lift the cowl assembly upward until it is clear of the blower assembly, then lay it on the table behind unit.

E.The air tower has two sections – a removable front section and the fixed rear section. The front section must be removed to access the temperature probe. A pair of slotted brackets, one at each end, holds the front section in place. Insert a 516-inch nut driver through the air outlet opening and turn the nuts on the outside studs counterclockwise to loosen them. Do not remove the nuts.

F.Grasp the bottom flange of the tower and push upward while rotating the bottom outward to disengage the two slotted brackets on the front section from the studs on the rear section.

4

Image 5
Contents Heated Pass Through Hour Service HotlineGeneral Parts Ordering and Service InformationInstallation/Set Up Operation Adjusting the Temperature MaintenanceService Procedures Replacing the Air Heater Replacing the Temperature Probe or High Limit ThermostatReplacing the Blower Assembly Replacing Other Electronic Components Wiring Diagram Component Common Repair Parts ListPage This page Intentionally Left Blank Service Hotline

none specifications

Frymaster is a renowned brand in the commercial kitchen equipment sector, primarily known for its high-quality fryers. With a history spanning decades, Frymaster has established itself as a leader in the frying equipment market by focusing on innovation and efficiency. One of the key features of Frymaster fryers is their advanced heating technology, which includes both open pot and flat bottom designs. This versatility allows operators to choose the fryer that best suits their specific needs, whether they are frying chicken, French fries, or other popular items.

One of the standout technologies integrated into Frymaster fryers is the oil filtration system. This feature extends the lifespan of frying oil, ensuring that food maintains a consistently high quality. The automated filtration processes allow for oil to be cleaned without requiring the fryer to be off for extended periods, which significantly boosts efficiency during peak business hours. Additionally, many Frymaster models come equipped with computerized controls that provide precise temperature management and cooking timers, ensuring that each batch of food is perfectly cooked.

Another characteristic that sets Frymaster apart is its focus on sustainability. Many models are designed to be energy-efficient, reducing both electricity consumption and operational costs. This is achieved through the use of efficient heating elements and advanced cooking technologies that optimize energy use. Frymaster also prioritizes the safety of users, incorporating features like automatic lift systems, which help prevent burns by allowing baskets to be raised and lowered safely.

Frymaster fryers are built with durability in mind, featuring robust materials that withstand the demands of a bustling commercial kitchen. The ease of cleaning is another advantage, with many fryers boasting removable components that simplify maintenance tasks.

Additionally, Frymaster offers a range of models to cater to various business sizes and culinary needs, from small kitchens to large-scale operations. The company's commitment to customer service and support further enhances its reputation, as they provide extensive resources to help users maximize the performance of their equipment.

In summary, Frymaster fryers are built on a foundation of technology, efficiency, and durability, making them a top choice for food service operators looking to enhance their cooking capabilities and achieve consistent and high-quality results.