Replacing Other Electronic Components | Frymaster none specification

HEATED PASS THROUGH

INSTALLATION, OPERATION, SERVICE, AND PARTS

F.Cut the wire ties on the wiring bundle and, one at a time, disconnect the wires from the failed assembly and connect the corresponding wire from the replacement motor.

G.Position the replacement motor over the mounting studs and secure it in place with the 5⁄16-inch nuts removed in Step D.

H.Reinstall the blower bridge and secure it in place with the 5⁄16-inch nuts removed in Step C.

I.Apply new acrylic tape (P/N 811-1042) to the HPT chassis, then stand the plate on its edge against the blower side of the unit.

J.Once the plate is properly aligned with the chassis, gently lower it into place.

K.Reconnect the plate ground wire to the push-on terminal on the back wall of the air tower.

L.Inspect the gaskets on the bottom of the cowl assembly and air tower assembly for damage. If necessary, remove the old gasket material, clean the surfaces thoroughly, and apply new gaskets.

M.Slip the slotted brackets on the front section of the air tower assembly up and under the nuts on the tower mounting screws. Push inward and down to ensure that the front section is properly seated.

N.Check for gaps in the seal between the front section of the air tower assembly and the plate. If a gap is present, remove the front section and apply a second gasket over the one already in place and reseat the front section.

O.Once the front section is properly positioned and seated, tighten the nuts on the mounting studs to pull it flush against the back of the tower assembly.

P.Carefully lower the cowl into position and check for a proper seal between the cowl and the plate. Install another gasket over the one already in place if there are gaps between the base of the cowl and the plate.

Q.Carefully turn the unit on its side and reinstall the five screws removed in Step B.

R.After the cowl is in place, reseal around the edges of the plate with RTV #108 silicone rubber compound, P/N 811-0511.

6.5Replacing Other Electronic Components

A.Disconnect the unit from the electrical power source.

B.Turn the unit on its side. Remove the five screws from the chassis bottom.

C.Set the unit down on its base.

D.Carefully lift the cowl assembly upward until it is clear of the blower assembly, then lay it on the table behind unit.

E.If replacing any component other than the ON/OFF switch, hold the replacement component next to the component to be replaced, disconnect the wires from the failed component and connect them to the new component. When all connections have been made, remove the failed component from its mounting and install the replacement component.

F.If replacing the ON/OFF switch, disconnect the wiring and push the switch out of the chassis. Press the replacement switch into the chassis and reconnect the wiring in accordance with the wiring diagram.

none specifications

Frymaster is a renowned brand in the commercial kitchen equipment sector, primarily known for its high-quality fryers. With a history spanning decades, Frymaster has established itself as a leader in the frying equipment market by focusing on innovation and efficiency. One of the key features of Frymaster fryers is their advanced heating technology, which includes both open pot and flat bottom designs. This versatility allows operators to choose the fryer that best suits their specific needs, whether they are frying chicken, French fries, or other popular items.

One of the standout technologies integrated into Frymaster fryers is the oil filtration system. This feature extends the lifespan of frying oil, ensuring that food maintains a consistently high quality. The automated filtration processes allow for oil to be cleaned without requiring the fryer to be off for extended periods, which significantly boosts efficiency during peak business hours. Additionally, many Frymaster models come equipped with computerized controls that provide precise temperature management and cooking timers, ensuring that each batch of food is perfectly cooked.

Another characteristic that sets Frymaster apart is its focus on sustainability. Many models are designed to be energy-efficient, reducing both electricity consumption and operational costs. This is achieved through the use of efficient heating elements and advanced cooking technologies that optimize energy use. Frymaster also prioritizes the safety of users, incorporating features like automatic lift systems, which help prevent burns by allowing baskets to be raised and lowered safely.

Frymaster fryers are built with durability in mind, featuring robust materials that withstand the demands of a bustling commercial kitchen. The ease of cleaning is another advantage, with many fryers boasting removable components that simplify maintenance tasks.

Additionally, Frymaster offers a range of models to cater to various business sizes and culinary needs, from small kitchens to large-scale operations. The company's commitment to customer service and support further enhances its reputation, as they provide extensive resources to help users maximize the performance of their equipment.

In summary, Frymaster fryers are built on a foundation of technology, efficiency, and durability, making them a top choice for food service operators looking to enhance their cooking capabilities and achieve consistent and high-quality results.