Wegener Communications DVR395 Section General Information, Introduction, Unpacking and Inspection

Page 9

Page 9

SECTION 1

GENERAL INFORMATION

1.1INTRODUCTION

This section contains instructions for connecting the Model DVR395/DVR396 Digital Video Receiver into a satellite receive system, and operating it in that mode.

1.2UNPACKING AND INSPECTION

Carefully unpack the unit and inspect it for obvious signs of physical damage, which might have occurred during shipment. Any damage claims must be reported to the carrier immediately. Be sure to check packing materials carefully for important documents and materials. Please contact Wegener Communications Customer Service Department with questions at (770) 814-4057 or fax (770) 232-0621. See Section 1.6 (Page 16) for more Technical Support assistance.

* * * WARNING * * *

This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

1.3PHYSICAL ENVIRONMENT

To avoid damage to this and other equipment, or personal injury, the following items should be strictly observed.

1.3.1DVR395 Desktop Version

The DVR395 Receiver may be installed on any reasonably level surface located in a clean, dry environment. Avoid locations subject to severe vibration or jarring impacts. The unit will meet the full 10 to 40oC operating temperature specification only if adequate ventilation is provided. Set it on a hard surface so that the mounting feet can maintain clearance under the unit. Avoid stacking objects or equipment against or on top of the unit where the vent holes would be blocked.

1.3.2DVR395 Rack-Mounting Version

Mount the DVR395 Receiver in a standard EIA 19-inch (48.3 Cm) equipment rack located in a clean, dry environment. Attach the front mounting ears at all four mounting points and do not stack any other equipment on the receiver. Check that the total rack current consumption is within the limits of the AC branch circuit and that a reliable earth safety ground is maintained. The unit will meet the full 10 to 40oC operating temperature specification only if adequate ventilation is provided. This requirement is easily met if the installer leaves one empty 1-3/4- inch (4.4 Cm) rack-unit space between units (50% rack utilization). Forced air is usually not

Page 9 of 30

DVR395/DVR396-002

Image 9
Contents Wegener R Communications Digital Video ReceiverThis Page Intentionally Left Blank DVR395/DVR396-002 Warranty This Page Intentionally Left Blank DVR395/DVR396-002 About this Manual Table of ContentsCross-references Other Viewing MethodsThis Page Intentionally Left Blank DVR395/DVR396-002 Table of Contents List of Illustrations List of TablesList of Cautions & Warnings Introduction Section General InformationUnpacking and Inspection Physical EnvironmentElevated Operating Ambient Equipment Specifications ParameterRear Panel Connections Ferrite Bead Installation For DVR396Connector Ferrite Size Ferrite InstallationRearDVR396 Panel DVR395 Rear PanelSecurity Labels DVR395/DVR396 Interconnect Descriptions Signal ConnectorSerial Port PIN Signal TX Data RX Data GroundDVR395 Serial Cables To Terminal or Printer RJ-12 DB-9 Female DB-25 MaleService@wegener.com To return a product for serviceTechnical Support ManualsControl DIP Switches Section Power on ProceduresFront Panel Controls and Indicators Control DIP Switch Functions Mode Setup FunctionsDVR395 Front Panel Front Panel Controls and Indicator Description LED & ALARM/WARNING ConditionsRED LED Indications Mode Condition Status LEDAmber GreenWelcome Banner Power on ProcedureThis Page Intentionally Left Blank DVR395/DVR396-002 Section Setup On Screen Display OSDSelect And Enter Key Functions For Carrier Select Customizing Settings for Your SystemCarrier Select TransportFor Signal Strength For Carrier StatusFor Serial Port Select Software Select For Software VersionAppendix a RMA Request Form Service@wegener.com Date of Change Rev Level Description of Change Record of RevisionsEmail service@wegener.com