Vent System USE, Vent System Care, Filters

5.Install cooktop according to manufacturer’s instructions. Check that rear of cooktop overlaps edge of retractable downdraft vent by ³⁄₈" (9.5 mm). See “Countertop Cutout Dimensions” in the “Location Requirements” section.

NOTE: To get the most efficient use from your new retractable downdraft vent, read the “Vent System Use” section.

VENT SYSTEM USE

The retractable downdraft vent system is designed to remove smoke, cooking vapors and odors from the cooktop area.

■For best results, the vent should be operating before cooking is started.

■If you use large or tall utensils, place them on the large rear element or burner surface.

■A higher heat setting than normally used may be needed when the downdraft vent is operating.

■This fan is suitable for use with solid-state speed controls.

Operating Downdraft Vent

To Use:

1.Push and hold the button on top of downdraft vent for a few seconds. (This slight delay helps avoid inadvertent raising of the vent during cleaning of the cooktop area.) Retractable section of downdraft vent will rise. Blower will begin to vent immediately if blower control knob slider is set to an “On” position.

2.Slide the control slider on the right-hand side of the downdraft vent to adjust the blower motor speed.

When cooking is complete:

1.Push the button on top of the retractable downdraft vent. The blower will turn off, and the retractable section of the vent will return to the closed position.

If a spill occurs on the cooktop that allows liquids to seep inside the downdraft, you must turn the downdraft off immediately. It is possible to cause damage to the downdraft if water is allowed inside the downdraft while it is operating.

1.Immediately turn off the downdraft at the speed control located on the right-hand side of the downdraft.

2.Turn off the power supply to the downdraft at the circuit breaker box or fuse box.

3.Allow plenty of time for the downdraft to dry naturally. Do not open the downdraft to remove the water.

VENT SYSTEM CARE

Surface of Downdraft Vent

To avoid damaging the finish, clean downdraft vent with soap and water. Do not use scouring powder or abrasive solutions.

Filters

Frequently remove and clean the filter(s) in the retractable section of the downdraft vent. This will improve the operating efficiency of the downdraft vent system.

To Remove Filters:

1.Place fingertips in the embossment at the top for the filters.

2.Press down on the filters far enough for the tab at the top of the filters to clear.

3.Pull forward to release the filter from its groove.

To Clean:

1.Remove the filter(s) and clean them in a dishwasher or in a hot detergent solution. The downdraft vent will not operate when the filters are not in place.

2.Dry the clean filter(s) and reinstall, making sure that they lock into place.

To Replace Filters:

1.Place filters into the retractable section of the downdraft vent.

2.Place fingertips into the embossment at the top of the filters and push down and back to allow the top tabs to snap into place.

NOTE: Downdraft will not operate if the filters are not in their proper position. If the filters’ top tabs are not locked behind the top flange, the vent may retract but not raise back up.

If retractable downdraft vent does not operate after clean filters have been installed:

Push the filter in as far as it will go. When the filter is removed, the microswitch behind the filter is inactivated. This feature will not allow the vent system to operate until the filter is properly installed.

A. Filter removal embossment

B. Left metal filter

C. Right metal filter

W10201609B specifications

The Jenn-Air W10201609B is a premium refrigerator water filter designed to enhance water and ice quality in residential kitchens. This filtration system stands out due to its advanced technology and user-friendly design, ensuring that homeowners receive clean, great-tasting water straight from their refrigerator dispenser.

One of the primary features of the W10201609B is its ability to reduce a wide array of contaminants commonly found in tap water. It efficiently removes impurities such as chlorine, lead, mercury, and sediments, which can not only affect taste but also pose health risks. By filtering out these harmful substances, it provides families with peace of mind knowing that the water they consume is safe.

The filter is designed with an easy installation process, making it accessible for anyone without the need for professional help. Users can seamlessly replace their existing filter within minutes, ensuring minimal downtime and hassle. Additionally, the filter is compatible with specific Jenn-Air refrigerator models, serving as a perfect fit for those who prioritize brand integrity and performance.

The W10201609B boasts a standard lifespan of up to six months, providing approximately 200 gallons of filtered water, depending on usage. This longevity makes it a cost-effective solution for households, as it reduces the frequency of filter replacements. Moreover, the filter uses a carbon block technology that significantly improves the taste and odor of water, providing a refreshing experience every time.

Furthermore, Jenn-Air’s commitment to innovation is evident in the filter's construction, which features a robust design that enhances durability and reliability. This ensures consistent performance, even in high-demand situations. The W10201609B is also NSF certified, which guarantees that it meets strict standards for public health and safety.

In summary, the Jenn-Air W10201609B water filter is an essential component for homeowners who prioritize quality in their drinking water. With its advanced filtration capabilities, easy installation, and impressive lifespan, it stands as a testament to Jenn-Air's dedication to providing cutting-edge kitchen solutions. Utilizing this filter not only upgrades the water quality in the home but also enhances the overall culinary experience, making it a worthy addition to any modern kitchen.