Jenn-Air W10201609B Determine which direction is best for your installation, Bottom venting

Page 9

5.Attach the left and right side end caps to the downdraft vent. Place the end cap upon the overcounter support, slide the tab into the slot and snap into place over the the plastic tabs.

A

A. End cap

6.Attach support legs to the side of the downdraft vent with 2 screws in each leg. Do not tighten screws.

A B

A. Blower motor box

B. Support leg

7.Using 2 or more people, insert the downdraft vent into the countertop cutout. Check that downdraft vent is parallel to side of cutout and that mounting brackets overlap countertop.

8.Move support legs down against cabinet floor. Place a level against the front of the downdraft vent base and adjust until downdraft vent is level vertically. Use a pencil to mark the top of each leg on the downdraft vent and the location of the support leg mounting holes on the cabinet floor.

A

B

A.Level

B.Mark locations.

9.Remove downdraft vent from cutout. Drill starter holes at each mounting screw location on the cabinet floor. Align top of legs with pencil marks on the face of the downdraft vent. Tighten screws in legs.

Determine which direction is best for your installation.

When installed in a cabinet, vent system can exhaust through the bottom, right, left or rear of the cabinet.

Bottom venting:

Downdraft vent is shipped with blower in down venting position so no modification is required. Go to Step 9.

Left or right venting:

1.Loosen the 2 hex/slotted head screws that attach the top bracket that secures the motor to the vent box enough to slide the bracket into the “Z” slots. This will move the bracket away from the top mounting lip of the blower box and allow it to tilt away from the vent box panel.

A

B

B

A. Bracket with “Z” slots

B. Hex/slotted head screws (2)

2.Lift up the blower box from the bottom mounting channel.

B

A

A. Blower box

B. Bottom mounting channel

3.Rotate it 90 degrees to the left or right so that the vent blower damper is repositioned in the direction needed. Do not twist or bind the wires or disconnect the wiring from the blower.

9

Image 9
Contents W10201609B Aspiration PAR LE BAS JENN-AIRR DETable DES Matières Your safety and the safety of others are very important Vent System SafetyInstallation Requirements Tools and PartsLocation Requirements Cabinet Dimensions Product DimensionsCountertop Cutout Dimensions Interior-mounted blower motor modelElectrical Requirements Venting RequirementsRecommended vent system length Venting Methods Interior Mounted Vent Motor Only Installation Instructions INTERIOR-MOUNTED Vent MotorIsland Location Calculating Vent System LengthInstall Vent System Example Vent SystemVent Piece Cm Round Determine which direction is best for your installation Bottom ventingLeft or right venting Rear Venting Plug in the wire connector to the blower motor Complete Installation Check Operation Make Electrical ConnectionsVent System Care Vent System USEOperating Downdraft Vent Surface of Downdraft Vent5x20 800 mA Time Delay Wiring DiagramAccessories Assistance or ServiceIf you need replacement parts U.S.AThis limited warranty does not cover JENN-AIRMAJOR Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE DU Système DextractionConservez CES Instructions Exigences demplacement Exigences DinstallationInstallation dans une résidence mobile Outillage et piècesPlan de travail Dimensions des ouvertures à découper Dimensions du produitDimensions du placard Modèle avec ventilateur monté à lintérieurLongueur recommandée pour le système d’extraction Spécifications électriquesExigences concernant lévacuation Instructions Dinstallation Ventilateur Monté À Lintérieur Configuration de cuisine en îlotCalcul de la longueur effective du système d’extraction Installation du système d’extraction Exemple de système d’extractionComposant Système de diamètre 6 15,2 cm Déterminer la meilleure direction pour l’installation Évacuation par le fondÉvacuation par le côté gauche ou par le côté droit Évacuation par l’arrière Débrancher le connecteur du câblage du moteur du ventilateur Vis 4 raccord de tuyau d’évacuation Ôter la vis fixant le couvercle du boîtier de connexion Achever linstallationContrôle du fonctionnement Raccordements électriquesUtilisation du système dextraction Utilisation DU Système DextractionUtilisation Lorsque la cuisson est terminéeEntretien DU Système Surface de lappareilFiltres Fusible temporisé, 5x20 800 mA Schéma DE CâblageAccessoires Assistance OU ServiceAux États-Unis Au CanadaLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers JENN-AIRW10201609B

W10201609B specifications

The Jenn-Air W10201609B is a premium refrigerator water filter designed to enhance water and ice quality in residential kitchens. This filtration system stands out due to its advanced technology and user-friendly design, ensuring that homeowners receive clean, great-tasting water straight from their refrigerator dispenser.

One of the primary features of the W10201609B is its ability to reduce a wide array of contaminants commonly found in tap water. It efficiently removes impurities such as chlorine, lead, mercury, and sediments, which can not only affect taste but also pose health risks. By filtering out these harmful substances, it provides families with peace of mind knowing that the water they consume is safe.

The filter is designed with an easy installation process, making it accessible for anyone without the need for professional help. Users can seamlessly replace their existing filter within minutes, ensuring minimal downtime and hassle. Additionally, the filter is compatible with specific Jenn-Air refrigerator models, serving as a perfect fit for those who prioritize brand integrity and performance.

The W10201609B boasts a standard lifespan of up to six months, providing approximately 200 gallons of filtered water, depending on usage. This longevity makes it a cost-effective solution for households, as it reduces the frequency of filter replacements. Moreover, the filter uses a carbon block technology that significantly improves the taste and odor of water, providing a refreshing experience every time.

Furthermore, Jenn-Air’s commitment to innovation is evident in the filter's construction, which features a robust design that enhances durability and reliability. This ensures consistent performance, even in high-demand situations. The W10201609B is also NSF certified, which guarantees that it meets strict standards for public health and safety.

In summary, the Jenn-Air W10201609B water filter is an essential component for homeowners who prioritize quality in their drinking water. With its advanced filtration capabilities, easy installation, and impressive lifespan, it stands as a testament to Jenn-Air's dedication to providing cutting-edge kitchen solutions. Utilizing this filter not only upgrades the water quality in the home but also enhances the overall culinary experience, making it a worthy addition to any modern kitchen.