Jenn-Air W10201609B Installation Requirements, Tools and Parts, Location Requirements

Page 4
Parts Needed
Two UL listed or CSA approved ½" (12.7 mm) conduit connectors.
Wall cap for interior-mounted motor (1) Vent system
Home power supply cable
UL listed wire connectors (4)
4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

Jigsaw or keyhole saw

Drill

¹⁄₈" (3 mm) drill bit for pilot holes

Pencil

Tape measure or ruler

Flat-blade screwdriver

Phillips screwdriver

³⁄₈" (9.5 mm) nut driver or ratchet

Level

Pliers

Metal snips

Wire stripper or utility knife

Caulking gun and weatherproof caulking compound

Vent clamps

Parts Supplied

A

CE

BD

A. Top trim (1)

B. End caps (2)

C. Overcounter support brackets (2)

D. Lower support legs (2)

E. Undercounter mounting brackets (2)

Other Parts Supplied

Bag of fasteners (1)

Metal cover (1)

Optional support and 2 screws (36" [91.4 cm] models only)

6" diameter backdraft damper

Location Requirements

NOTE: Downdraft vent is installed directly behind the cooktop. Install the downdraft vent first, then install the cooktop.

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the downdraft vent. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the front of the downdraft vent above the terminal box cover.

Downdraft vent location should be away from strong draft areas, such as windows, doors, and strong heating vents or fans.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Consult the cooktop manufacturer installation instructions before making any cutouts.

Check that the downdraft vent and cooktop location will clear the cabinet walls, backsplash, and rear wall studs inside the cabinet.

Check for the minimum distance between the front edge of the countertop and the front edge of the cooktop. The minimum horizontal distance between the overhead cabinets is the same as the width of the installed downdraft vent.

All openings in ceiling and wall where the downdraft vent will be installed must be sealed.

Grounded electrical outlet is required. See “Electrical Requirements” section.

When installing the downdraft vent, the cabinet drawer will need to be removed and the drawer front installed permanently to the cabinet.

Cabinet Construction:

Downdraft vent is designed for use in a cabinet with a depth of 24" (61 cm). Some installations require a countertop deeper than 25" (63.5 cm). See the Countertop Cutout Dimensions section.

The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets installed at either side of the downdraft vent must be 18" (45.7 cm) above the cooking surface.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

Image 4
Contents Aspiration PAR LE BAS JENN-AIRR DE W10201609BTable DES Matières Vent System Safety Your safety and the safety of others are very importantTools and Parts Installation RequirementsLocation Requirements Product Dimensions Cabinet DimensionsCountertop Cutout Dimensions Interior-mounted blower motor modelVenting Requirements Electrical RequirementsRecommended vent system length Installation Instructions INTERIOR-MOUNTED Vent Motor Venting Methods Interior Mounted Vent Motor OnlyIsland Location Calculating Vent System LengthExample Vent System Install Vent SystemVent Piece Cm Round Bottom venting Determine which direction is best for your installationLeft or right venting Rear Venting Plug in the wire connector to the blower motor Complete Installation Make Electrical Connections Check OperationVent System USE Vent System CareOperating Downdraft Vent Surface of Downdraft VentWiring Diagram 5x20 800 mA Time DelayAssistance or Service AccessoriesIf you need replacement parts U.S.AJENN-AIRMAJOR Appliance Warranty This limited warranty does not coverSécurité DE DU Système Dextraction Votre sécurité et celle des autres est très importanteConservez CES Instructions Exigences Dinstallation Exigences demplacementInstallation dans une résidence mobile Outillage et piècesDimensions du produit Plan de travail Dimensions des ouvertures à découperDimensions du placard Modèle avec ventilateur monté à lintérieurSpécifications électriques Longueur recommandée pour le système d’extractionExigences concernant lévacuation Configuration de cuisine en îlot Instructions Dinstallation Ventilateur Monté À LintérieurCalcul de la longueur effective du système d’extraction Exemple de système d’extraction Installation du système d’extractionComposant Système de diamètre 6 15,2 cm Évacuation par le fond Déterminer la meilleure direction pour l’installationÉvacuation par le côté gauche ou par le côté droit Évacuation par l’arrière Débrancher le connecteur du câblage du moteur du ventilateur Vis 4 raccord de tuyau d’évacuation Achever linstallation Ôter la vis fixant le couvercle du boîtier de connexionRaccordements électriques Contrôle du fonctionnementUtilisation DU Système Dextraction Utilisation du système dextractionUtilisation Lorsque la cuisson est terminéeSurface de lappareil Entretien DU SystèmeFiltres Schéma DE Câblage Fusible temporisé, 5x20 800 mAAssistance OU Service AccessoiresAux États-Unis Au CanadaGarantie DES Gros Appareils Ménagers JENN-AIR La présente garantie limitée ne couvre pasW10201609B

W10201609B specifications

The Jenn-Air W10201609B is a premium refrigerator water filter designed to enhance water and ice quality in residential kitchens. This filtration system stands out due to its advanced technology and user-friendly design, ensuring that homeowners receive clean, great-tasting water straight from their refrigerator dispenser.

One of the primary features of the W10201609B is its ability to reduce a wide array of contaminants commonly found in tap water. It efficiently removes impurities such as chlorine, lead, mercury, and sediments, which can not only affect taste but also pose health risks. By filtering out these harmful substances, it provides families with peace of mind knowing that the water they consume is safe.

The filter is designed with an easy installation process, making it accessible for anyone without the need for professional help. Users can seamlessly replace their existing filter within minutes, ensuring minimal downtime and hassle. Additionally, the filter is compatible with specific Jenn-Air refrigerator models, serving as a perfect fit for those who prioritize brand integrity and performance.

The W10201609B boasts a standard lifespan of up to six months, providing approximately 200 gallons of filtered water, depending on usage. This longevity makes it a cost-effective solution for households, as it reduces the frequency of filter replacements. Moreover, the filter uses a carbon block technology that significantly improves the taste and odor of water, providing a refreshing experience every time.

Furthermore, Jenn-Air’s commitment to innovation is evident in the filter's construction, which features a robust design that enhances durability and reliability. This ensures consistent performance, even in high-demand situations. The W10201609B is also NSF certified, which guarantees that it meets strict standards for public health and safety.

In summary, the Jenn-Air W10201609B water filter is an essential component for homeowners who prioritize quality in their drinking water. With its advanced filtration capabilities, easy installation, and impressive lifespan, it stands as a testament to Jenn-Air's dedication to providing cutting-edge kitchen solutions. Utilizing this filter not only upgrades the water quality in the home but also enhances the overall culinary experience, making it a worthy addition to any modern kitchen.