Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Inserting And Replacing The Laser Batteries Fig. G, Fig. H, Fig. J

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 20

INSERTING AND REPLACING THE LASER BATTERIES (FIG. G)

INSERTING AND REPLACING THE LASER BATTERIES (FIG. G)

• Unplug your miter saw.

!WARNING

Failure to unplug your tool could result in accidental starting and cause possible serious personal injury.

1.Open the battery cover (1).

2.Insert the two supplied AAA batteries in the case as per the diagram below. If replacing the batteries, take out the old batteries and place with new AAA batteries. Dispose of old batteries properly.

3.Close the battery cover (1).

NOTE: Replace the batteries with batteries that have a rating of 1.5 V (Number 4 series and AAA size or equivalent).

Fig. G

1

REMOVING AND INSTALLING THE BLADE

Removing Blade (Fig. H, I, J, K)

1.Unplug the saw from the outlet.

2.Allow the blade assembly to rise to the uppermost position. Raise the lower blade guard (1) to the upper position.

3.Loosen the cover plate screw (2) using a star-head screwdriver.

4.Rotate the cover plate (3) to expose the arbor bolt (4).

5.Place the blade wrench over the arbor bolt.

Fig. H

1

2

Fig. I

3

4

6.Locate the arbor lock (5) on the motor below the miter saw switch handle.

7.Press the arbor lock, holding it in ﬁrmly while turning the blade wrench clockwise. The arbor lock will engage after turning the wrench. Continue to hold the arbor lock to keep it engaged while turning the wrench clockwise to loosen the arbor bolt.

Fig. J

5

20

Image 20

Craftsman 137.37564 manual Inserting And Replacing The Laser Batteries Fig. G, Fig. H, Fig. J

Contents

Customer Help Line For Technical Support Sears Parts & Repair CenterOperator’s Manual 12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model NoTABLE OF CONTENTS WARRANTYCRAFTSMAN FULL WARRANTY PAGEPRODUCT SPECIFICATIONS MOTORMITER SAW Cutting CapacitySYMBOLS ! DANGER ! WARNING ! CAUTIONPROHIBITION SUPPORT AND CLAMP WORKPOWER TOOL SAFETY 12. ALWAYS WEAR EYE ! DANGER 27. WEAR HEARING7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust DUAL BEVEL COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 23.NEVER use the miter saw in areas with ﬂammable liquids or gases 25.SHUT OFF the power before servicing or adjusting the tool27.MAKE SURE the work area is clean before leaving the machine ELECTRICAL REQUIREMENTS AND SAFETY ! CAUTION Three-Pronged Plug Grounding Prong Properly GroundedThree-Pronged Receptacle Grounding Lug Make sure this is connected to a known groundACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIESACCESSORIES BLADE INFORMATIONCOMBINATION SQUARE MUST BE TRUE TOOLS NEEDED FOR ASSEMBLYSuppliedNot supplied CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY INSTALLING THE EXTENSION WING ASSEMBLY FIG. D INSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. FFig. D SAW BLADE WRENCH FIG. EREMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, K INSERTING AND REPLACING THE LASER BATTERIES FIG. GFig. G Fig. HFig. K MOUNTING THE MITER SAW ADJUSTMENTS BEVEL STOP ADJUSTMENT90 Bevel adjustment Fig. N, O 90 Bevel Pointer Adjustment Fig. P45 Right Bevel Positive Stop Adjustment Fig. Q 45 Left Bevel Positive Stop Adjustment Fig. RFig. P Fig. Q33.9 Right Bevel Adjustment Fig. S MITER ANGLE ADJUSTMENT FIG. V, W MITER SCALE INDICATOR FIG. WSQUARING THE FENCE FIG. U Fig. UQUICK-CAM MITER TABLE LOCK OPERATION FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG OPERATION INSPECT YOUR WORKPIECE DRESS FOR SAFETYPLAN YOUR WORK WHEN SAW IS RUNNING DO NOT OVERREACHNever cut freehand USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECESBODY AND HAND POSITION FIG. Y Fig. Z-1 Laser Warning Labelcutting line Fig. Z-2TO TURN SAW ON FIG. AA BEFORE LEAVING THE SAW To avoid injury from materials being thrown, always unplug the sawMITER CUT FIG. CC Fig. CCCOMPOUND CUT FIG. FF Fig. HH Fig. KK Bevel/Miter SettingsCUTTING CROWN MOULDING FIG. KK, LL CHANGING THE BELT FIG. MM Fig. MMCompound Miter Saw CROWN MOLDING CHARTMiter and Bevel Angle Settings Wall to Crown Molding Angle MAINTENANCE ! DANGERLUBRICATION FIG. OO TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE - MOTORPROBLEM PROBLEM CAUSETROUBLESHOOTING GUIDE Vacuum or blow out dust. WEARPARTS LIST PARTS LIST FOR MITER SAW - PART A12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOPARTS LIST FOR MITER SAW - PART B 12 IN. DUAL BEVEL COMPOUND MITER SAWMODEL NO I.D. DescriptionX62Y Q’ty DescriptionSize Here’s what the Repair Protection Agreement* includes Sears Installation ServiceREPAIR PROTECTION AGREEMENTS Our Home Get it fixed, at your home or oursYour Home