Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Adjustments, Bevel Stop Adjustment, Bevel adjustment Fig. N, O, Fig. O

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 23

ADJUSTMENTS

ADJUSTMENTS

BEVEL STOP ADJUSTMENT

!WARNING

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

90° Bevel adjustment (Fig. N, O)

1.Loosen bevel lock handle (1), and tilt the cutting arm completely to the right. Tighten the bevel lock handle. Lower blade.

2.Place a combination square (2) on the miter table with the rule against the table and the heel of the square against the saw blade.

3.If the blade is not 90° (0°) square with the miter table, loosen the bevel lock handle (1), tilt the cutting head completely to the left, loosen the lock nut (3) on the bevel angle adjustment bolt (4) and adjust the bolt (4) in or out to increase or decrease the bevel angle with a 10 mm wrench.

4.Tilt the cutting arm to back to the right at 90° (0°) bevel and recheck for alignment.

5.Repeat steps 1 through 4 if further adjustment is needed.

6.Tighten the bevel lock handle (1) and lock nut (3) when alignment is achieved.

Fig. N

1

2

Fig. O

4

3

90° Bevel Pointer Adjustment (Fig. P)

1.When the blade is exactly 90° (0°) to the table, loosen the bevel indicator screws (5) using a star- head screwdriver.

2.Adjust bevel indicators (6) to the “0” mark on the bevel scale and retighten the screw.

23

Image 23

Craftsman 137.37564 manual Adjustments, Bevel Stop Adjustment, Bevel adjustment Fig. N, O, Fig. O

Contents

12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model No Customer Help Line For Technical SupportSears Parts & Repair Center Operator’s ManualPAGE TABLE OF CONTENTSWARRANTY CRAFTSMAN FULL WARRANTYCutting Capacity PRODUCT SPECIFICATIONSMOTOR MITER SAWSUPPORT AND CLAMP WORK SYMBOLS! DANGER ! WARNING ! CAUTION PROHIBITIONPOWER TOOL SAFETY 12. ALWAYS WEAR EYE 27. WEAR HEARING ! DANGER7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust DUAL BEVEL COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 23.NEVER use the miter saw in areas with ﬂammable liquids or gases 25.SHUT OFF the power before servicing or adjusting the tool27.MAKE SURE the work area is clean before leaving the machine ELECTRICAL REQUIREMENTS AND SAFETY Grounding Lug Make sure this is connected to a known ground ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Three-Pronged ReceptacleBLADE INFORMATION ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES ACCESSORIESCOMBINATION SQUARE MUST BE TRUE TOOLS NEEDED FOR ASSEMBLYSuppliedNot supplied CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY SAW BLADE WRENCH FIG. E INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F Fig. DFig. H REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. GFig. K MOUNTING THE MITER SAW 90 Bevel Pointer Adjustment Fig. P ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel adjustment Fig. N, OFig. Q 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. P33.9 Right Bevel Adjustment Fig. S Fig. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W SQUARING THE FENCE FIG. UQUICK-CAM MITER TABLE LOCK OPERATION FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG OPERATION INSPECT YOUR WORKPIECE DRESS FOR SAFETYPLAN YOUR WORK USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WHEN SAW IS RUNNINGDO NOT OVERREACH Never cut freehandBODY AND HAND POSITION FIG. Y Fig. Z-2 Fig. Z-1Laser Warning Label cutting lineTO TURN SAW ON FIG. AA Fig. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw MITER CUT FIG. CCCOMPOUND CUT FIG. FF Fig. HH Fig. KK Bevel/Miter SettingsCUTTING CROWN MOULDING FIG. KK, LL Fig. MM CHANGING THE BELT FIG. MMCompound Miter Saw CROWN MOLDING CHARTMiter and Bevel Angle Settings Wall to Crown Molding Angle ! DANGER MAINTENANCELUBRICATION FIG. OO PROBLEM CAUSE TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEMVacuum or blow out dust. WEAR TROUBLESHOOTING GUIDEMODEL NO PARTS LISTPARTS LIST FOR MITER SAW - PART A 12 IN. DUAL BEVEL COMPOUND MITER SAWI.D. Description PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOX62Y Q’ty DescriptionSize Here’s what the Repair Protection Agreement* includes Sears Installation ServiceREPAIR PROTECTION AGREEMENTS Our Home Get it fixed, at your home or oursYour Home