Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Troubleshooting Guide, Vacuum or blow out dust. WEAR

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 43

Vacuum or blow out dust. WEAR

TROUBLESHOOTING GUIDE

!WARNING

To avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing the blade or making adjustments.

TROUBLESHOOTING GUIDE - SAW OPERATION

PROBLEM		PROBLEM CAUSE		SUGGESTED CORRECTIVE
PROBLEM		PROBLEM CAUSE		ACTION
				ACTION
Blade hits table.	1.	Misalignment.	1.	See ADJUSTMENT - Cutting
				Arm Travel section.

Angle of cut not	1.	Miter table unlocked.	1.	See OPERATION - Miter Angle
accurate. Can	2.	Sawdust under table.		Adjustment section.
not adjust miter.			2.	Vacuum or blow out dust. WEAR
				EYE PROTECTION.

Cutting arm	1.	Loose pivot points.	1.	See ADJUSTMENT - Cutting
wobbles.				Arm Travel section.

Cutting arm will	1.	Pivot spring not replaced	1.	Contact Sears Service Center.
not fully raise, or		properly after service.	2.	See MAINTENANCE section.
blade guard	2.	Sawdust build-up.
won’t fully close.

Blade binds,	1.	Improper operation.	1.	See BASIC SAW OPERATION
jams, burns	2.	Dull or warped blade.		section.
wood.	3.	Improper blade size.	2.	Replace or sharpen blade.
	4	Wood is moving during	3.	Replace with 12 in. diameter
		cut.		blade.
			4.	Use hold down clamp to secure
				workpiece to table.

Saw vibrates or	1.	Saw blade not round /	1.	Replace blade.
shakes.		damaged / loose.	2.	Tighten arbor bolt.
	2.	Arbor bolt loose.

43

Image 43

Craftsman 137.37564 manual Troubleshooting Guide, Vacuum or blow out dust. WEAR

Contents

12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model No Customer Help Line For Technical SupportSears Parts & Repair Center Operator’s ManualPAGE TABLE OF CONTENTSWARRANTY CRAFTSMAN FULL WARRANTYCutting Capacity PRODUCT SPECIFICATIONSMOTOR MITER SAWSUPPORT AND CLAMP WORK SYMBOLS! DANGER ! WARNING ! CAUTION PROHIBITIONPOWER TOOL SAFETY 12. ALWAYS WEAR EYE 27. WEAR HEARING ! DANGERSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW DUAL BEVEL COMPOUND MITER SAW SAFETY7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust 27.MAKE SURE the work area is clean before leaving the machine 25.SHUT OFF the power before servicing or adjusting the tool23.NEVER use the miter saw in areas with ﬂammable liquids or gases ELECTRICAL REQUIREMENTS AND SAFETY Grounding Lug Make sure this is connected to a known ground ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Three-Pronged ReceptacleBLADE INFORMATION ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES ACCESSORIESSuppliedNot supplied TOOLS NEEDED FOR ASSEMBLYCOMBINATION SQUARE MUST BE TRUE CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY SAW BLADE WRENCH FIG. E INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F Fig. DFig. H REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. GFig. K MOUNTING THE MITER SAW 90 Bevel Pointer Adjustment Fig. P ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel adjustment Fig. N, OFig. Q 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. P33.9 Right Bevel Adjustment Fig. S Fig. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W SQUARING THE FENCE FIG. UQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK OPERATION FIG OPERATION PLAN YOUR WORK DRESS FOR SAFETYINSPECT YOUR WORKPIECE USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WHEN SAW IS RUNNINGDO NOT OVERREACH Never cut freehandBODY AND HAND POSITION FIG. Y Fig. Z-2 Fig. Z-1Laser Warning Label cutting lineTO TURN SAW ON FIG. AA Fig. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw MITER CUT FIG. CCCOMPOUND CUT FIG. FF Fig. HH CUTTING CROWN MOULDING FIG. KK, LL Bevel/Miter SettingsFig. KK Fig. MM CHANGING THE BELT FIG. MMMiter and Bevel Angle Settings Wall to Crown Molding Angle CROWN MOLDING CHARTCompound Miter Saw ! DANGER MAINTENANCELUBRICATION FIG. OO PROBLEM CAUSE TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEMVacuum or blow out dust. WEAR TROUBLESHOOTING GUIDEMODEL NO PARTS LISTPARTS LIST FOR MITER SAW - PART A 12 IN. DUAL BEVEL COMPOUND MITER SAWI.D. Description PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOX62Y Size DescriptionQ’ty REPAIR PROTECTION AGREEMENTS Sears Installation ServiceHere’s what the Repair Protection Agreement* includes Your Home Get it fixed, at your home or oursOur Home