Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 Troubleshooting Guide - Motor, Problem Cause, Suggested Corrective

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 42

TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE

!WARNING

To avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing the blade or making adjustments.

TROUBLESHOOTING GUIDE - MOTOR

PROBLEM		PROBLEM CAUSE	SUGGESTED CORRECTIVE
PROBLEM		PROBLEM CAUSE		ACTION
				ACTION
Brake does not	1.	Motor brushes not sealed	1.	Inspect/clean/replace
stop blade within		or lightly sticking.		brushes. See
10 seconds.	2.	Motor brake overheated		MAINTENANCE section.
		from use of defective or	2.	Use the blade speciﬁed in
		wrong size blade or rapid		this Operator’s Manual. Let
		ON/OFF cycling.		cool down. See REMOVING
	3.	Arbor bolt loose.		OR INSTALLING THE BLADE
	4.	Brushes cracked,		section.
		damaged, etc.	3.	Retighten. See REMOVING
	5. Other.			OR INSTALLING THE
				BLADE section.
			4.	Replace brushes.
			5.	Contact the Customer Help
				Line at 1-800-843-1682.
Motor does not	1.	Limit switch failure	1.	Replace limit switch.
start	2.	Brush worn.	2.	Replace brushes. See
	3.	Fuse blown or circuit		MAINTENANCE section.
		breaker tripped on home	3.	Verify there is electrical
		panel.		power at the outlet.
	4.	Other.	4.	Contact Contact the
				Customer Help Line at
				1-800-843-1682.

Brush spark when	1.	Brush worn.	1.	Replace Brushes. See
switch released.	2.	Other.		MAINTENANCE section.
			2.	Contact the Customer Help
				Line at 1-800-843-1682.

42

Image 42

Craftsman 137.37564 manual Troubleshooting Guide - Motor, Problem Cause, Suggested Corrective, Action

Contents

Operator’s Manual Customer Help Line For Technical SupportSears Parts & Repair Center 12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model NoCRAFTSMAN FULL WARRANTY TABLE OF CONTENTSWARRANTY PAGEMITER SAW PRODUCT SPECIFICATIONSMOTOR Cutting CapacityPROHIBITION SYMBOLS! DANGER ! WARNING ! CAUTION SUPPORT AND CLAMP WORKPOWER TOOL SAFETY 12. ALWAYS WEAR EYE ! DANGER 27. WEAR HEARINGDUAL BEVEL COMPOUND MITER SAW SAFETY SPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust 25.SHUT OFF the power before servicing or adjusting the tool 27.MAKE SURE the work area is clean before leaving the machine23.NEVER use the miter saw in areas with ﬂammable liquids or gases ELECTRICAL REQUIREMENTS AND SAFETY Three-Pronged Receptacle ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Grounding Lug Make sure this is connected to a known groundACCESSORIES ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES BLADE INFORMATIONTOOLS NEEDED FOR ASSEMBLY SuppliedNot suppliedCOMBINATION SQUARE MUST BE TRUE CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY Fig. D INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F SAW BLADE WRENCH FIG. EFig. G REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. HFig. K MOUNTING THE MITER SAW 90 Bevel adjustment Fig. N, O ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel Pointer Adjustment Fig. PFig. P 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. Q33.9 Right Bevel Adjustment Fig. S SQUARING THE FENCE FIG. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W Fig. UPOSITIVE STOP MITER ANGLE ADJUSTMENT FIG QUICK-CAM MITER TABLE LOCK ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK OPERATION FIG OPERATION DRESS FOR SAFETY PLAN YOUR WORKINSPECT YOUR WORKPIECE Never cut freehand WHEN SAW IS RUNNINGDO NOT OVERREACH USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECESBODY AND HAND POSITION FIG. Y cutting line Fig. Z-1Laser Warning Label Fig. Z-2TO TURN SAW ON FIG. AA MITER CUT FIG. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw Fig. CCCOMPOUND CUT FIG. FF Fig. HH Bevel/Miter Settings CUTTING CROWN MOULDING FIG. KK, LLFig. KK CHANGING THE BELT FIG. MM Fig. MMCROWN MOLDING CHART Miter and Bevel Angle Settings Wall to Crown Molding AngleCompound Miter Saw MAINTENANCE ! DANGERLUBRICATION FIG. OO PROBLEM TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEM CAUSETROUBLESHOOTING GUIDE Vacuum or blow out dust. WEAR12 IN. DUAL BEVEL COMPOUND MITER SAW PARTS LISTPARTS LIST FOR MITER SAW - PART A MODEL NOMODEL NO PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW I.D. DescriptionX62Y Description SizeQ’ty Sears Installation Service REPAIR PROTECTION AGREEMENTSHere’s what the Repair Protection Agreement* includes Get it fixed, at your home or ours Your HomeOur Home