Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Compound Cut Fig. Ff

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 35

COMPOUND CUT (FIG. FF)

!WARNING

The sliding fence must be extended to the left when making bevel cuts. The sliding fence has been notched three bevel angles where the user must adjust the fence to match the degree of the bevel cut. Failure to extend the sliding fence will not allow enough space for the blade to pass through which could result in serious injury. At extreme miter or bevel angles the saw blade may also come in contact with the fence.

COMPOUND CUT (FIG. FF)

A compound cut is the combination of a miter and a bevel cut simultaneously.

1.Extend the sliding fence as described in “SLIDING FENCE”.

2.Loosen the bevel lock handle (1) and position the cutting head at the desired bevel position. Lock the bevel lock handle.

3.Release miter lock lever (2). Press down the positive stop locking lever

(3) and position the table at the desired angle. Release the positive stop locking lever and lock the miter lock lever.

Fig. FF

1

2

3

CUTTING BOWED MATERIAL (FIG. GG)

A bowed workpiece must be positioned against the fence and secured with a clamping devise before cutting. Do not position workpiece incorrectly or try to cut the workpiece without the support of the fence. This will cause the blade to bind, and could result in personal injury.

Fig. GG

WORKPIECE SUPPORT AND REPETITIVE CUTTING USING THE STOP PLATE (FIG. HH)

Long pieces need extension table support.

1.Loosen the knob (1), and then slide the extension wing to desired position and tighten the knob.

2.The arm bracket is designed for use during repetitive cutting. Only use one stop plate at a time. Loosen the locking knobs (2), raise the arm bracket (3), and retighten the locking knobs.

35

Image 35

Craftsman 137.37564 manual Compound Cut Fig. Ff

Contents

12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model No Customer Help Line For Technical SupportSears Parts & Repair Center Operator’s ManualPAGE TABLE OF CONTENTSWARRANTY CRAFTSMAN FULL WARRANTYCutting Capacity PRODUCT SPECIFICATIONSMOTOR MITER SAWSUPPORT AND CLAMP WORK SYMBOLS! DANGER ! WARNING ! CAUTION PROHIBITIONPOWER TOOL SAFETY 12. ALWAYS WEAR EYE 27. WEAR HEARING ! DANGER7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust DUAL BEVEL COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 23.NEVER use the miter saw in areas with ﬂammable liquids or gases 25.SHUT OFF the power before servicing or adjusting the tool27.MAKE SURE the work area is clean before leaving the machine ELECTRICAL REQUIREMENTS AND SAFETY Grounding Lug Make sure this is connected to a known ground ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Three-Pronged ReceptacleBLADE INFORMATION ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES ACCESSORIESCOMBINATION SQUARE MUST BE TRUE TOOLS NEEDED FOR ASSEMBLYSuppliedNot supplied CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY SAW BLADE WRENCH FIG. E INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F Fig. DFig. H REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. GFig. K MOUNTING THE MITER SAW 90 Bevel Pointer Adjustment Fig. P ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel adjustment Fig. N, OFig. Q 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. P33.9 Right Bevel Adjustment Fig. S Fig. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W SQUARING THE FENCE FIG. UQUICK-CAM MITER TABLE LOCK OPERATION FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG OPERATION INSPECT YOUR WORKPIECE DRESS FOR SAFETYPLAN YOUR WORK USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WHEN SAW IS RUNNINGDO NOT OVERREACH Never cut freehandBODY AND HAND POSITION FIG. Y Fig. Z-2 Fig. Z-1Laser Warning Label cutting lineTO TURN SAW ON FIG. AA Fig. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw MITER CUT FIG. CCCOMPOUND CUT FIG. FF Fig. HH Fig. KK Bevel/Miter SettingsCUTTING CROWN MOULDING FIG. KK, LL Fig. MM CHANGING THE BELT FIG. MMCompound Miter Saw CROWN MOLDING CHARTMiter and Bevel Angle Settings Wall to Crown Molding Angle ! DANGER MAINTENANCELUBRICATION FIG. OO PROBLEM CAUSE TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEMVacuum or blow out dust. WEAR TROUBLESHOOTING GUIDEMODEL NO PARTS LISTPARTS LIST FOR MITER SAW - PART A 12 IN. DUAL BEVEL COMPOUND MITER SAWI.D. Description PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOX62Y Q’ty DescriptionSize Here’s what the Repair Protection Agreement* includes Sears Installation ServiceREPAIR PROTECTION AGREEMENTS Our Home Get it fixed, at your home or oursYour Home