Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Dual Bevel Compound Miter Saw Safety

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 8

DUAL BEVEL COMPOUND MITER SAW SAFETY

DUAL BEVEL COMPOUND MITER SAW SAFETY

SPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW

1.DO NOT operate the miter saw until it is completely assembled and installed according to these instructions.

2.IF YOU ARE NOT thoroughly familiar with the operation of miter saws, seek guidance from your supervisor, instructor or other qualiﬁed person.

3.ALWAYS hold the work ﬁrmly against the fence and table. DO NOT perform any operation freehand (use clamp wherever possible).

4.KEEP HANDS out of the path of the saw blade. If the workpiece you are cutting would cause your hands to be within 8-3/25 in. of the saw blade, the workpiece should be clamped in place before making the cut.

5.MAKE SURE the blade is sharp, runs freely and is free of vibration.

6.ALLOW the motor to come up to full speed before starting a cut.

7.KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust.

8.ALWAYS MAKE SURE all handles are tight before cutting, even if the table is positioned in one of the positive stops.

9.MAKE SURE both the blade and the collar are clean and the arbor bolt is tightened securely.

10.USE only blade collars speciﬁed for your saw.

11.NEVER use blades larger than

12 inches in diameter.

12.NEVER apply lubricants to the blade when the saw is running.

13.ALWAYS check the blade for cracks or damage before operation. Replace a cracked or damaged blade immediately.

14.NEVER use blades recommended for operation at less than 4800 RPM.

15.ALWAYS keep the blade guards in place and use at all times.

16.NEVER reach around the saw blade.

17.MAKE SURE the blade is not in contact with the workpiece before the switch is turned ON.

18.IMPORTANT: After completing a cut, release the trigger switch and wait for the blade to stop before returning the saw to the raised position.

19.MAKE SURE the blade has come to a complete stop before removing or securing the workpiece, changing the workpiece angle or changing the angle of the blade.

8

Image 8

Craftsman 137.37564 manual Dual Bevel Compound Miter Saw Safety, Specific Safety Instructions For This Compound Miter Saw

Contents

Customer Help Line For Technical Support Sears Parts & Repair CenterOperator’s Manual 12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model NoTABLE OF CONTENTS WARRANTYCRAFTSMAN FULL WARRANTY PAGEPRODUCT SPECIFICATIONS MOTORMITER SAW Cutting CapacitySYMBOLS ! DANGER ! WARNING ! CAUTIONPROHIBITION SUPPORT AND CLAMP WORKPOWER TOOL SAFETY 12. ALWAYS WEAR EYE ! DANGER 27. WEAR HEARING7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust DUAL BEVEL COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 23.NEVER use the miter saw in areas with ﬂammable liquids or gases 25.SHUT OFF the power before servicing or adjusting the tool27.MAKE SURE the work area is clean before leaving the machine ELECTRICAL REQUIREMENTS AND SAFETY ! CAUTION Three-Pronged Plug Grounding Prong Properly GroundedThree-Pronged Receptacle Grounding Lug Make sure this is connected to a known groundACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIESACCESSORIES BLADE INFORMATIONCOMBINATION SQUARE MUST BE TRUE TOOLS NEEDED FOR ASSEMBLYSuppliedNot supplied CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY INSTALLING THE EXTENSION WING ASSEMBLY FIG. D INSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. FFig. D SAW BLADE WRENCH FIG. EREMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, K INSERTING AND REPLACING THE LASER BATTERIES FIG. GFig. G Fig. HFig. K MOUNTING THE MITER SAW ADJUSTMENTS BEVEL STOP ADJUSTMENT90 Bevel adjustment Fig. N, O 90 Bevel Pointer Adjustment Fig. P45 Right Bevel Positive Stop Adjustment Fig. Q 45 Left Bevel Positive Stop Adjustment Fig. RFig. P Fig. Q33.9 Right Bevel Adjustment Fig. S MITER ANGLE ADJUSTMENT FIG. V, W MITER SCALE INDICATOR FIG. WSQUARING THE FENCE FIG. U Fig. UQUICK-CAM MITER TABLE LOCK OPERATION FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG OPERATION INSPECT YOUR WORKPIECE DRESS FOR SAFETYPLAN YOUR WORK WHEN SAW IS RUNNING DO NOT OVERREACHNever cut freehand USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECESBODY AND HAND POSITION FIG. Y Fig. Z-1 Laser Warning Labelcutting line Fig. Z-2TO TURN SAW ON FIG. AA BEFORE LEAVING THE SAW To avoid injury from materials being thrown, always unplug the sawMITER CUT FIG. CC Fig. CCCOMPOUND CUT FIG. FF Fig. HH Fig. KK Bevel/Miter SettingsCUTTING CROWN MOULDING FIG. KK, LL CHANGING THE BELT FIG. MM Fig. MMCompound Miter Saw CROWN MOLDING CHARTMiter and Bevel Angle Settings Wall to Crown Molding Angle MAINTENANCE ! DANGERLUBRICATION FIG. OO TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE - MOTORPROBLEM PROBLEM CAUSETROUBLESHOOTING GUIDE Vacuum or blow out dust. WEARPARTS LIST PARTS LIST FOR MITER SAW - PART A12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOPARTS LIST FOR MITER SAW - PART B 12 IN. DUAL BEVEL COMPOUND MITER SAWMODEL NO I.D. DescriptionX62Y Q’ty DescriptionSize Here’s what the Repair Protection Agreement* includes Sears Installation ServiceREPAIR PROTECTION AGREEMENTS Our Home Get it fixed, at your home or oursYour Home