Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 ! Caution, Three-Pronged Plug Grounding Prong Properly Grounded, Two-Pronged

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 11

Three-Pronged Plug

NOTE: When using an extension cord on a circuit with a #14 wire, the extension cord must not exceed 25 feet in length. Before connecting the motor to the power line, make sure the switch is in the off position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor. This tool is intended for use on a circuit that has a receptacle like the one illustrated in Fig. 1.

Fig. 1 shows a three-pronged electrical plug and receptacle that has a grounding conductor. If a properly

Fig. 1

Three-Pronged Plug

Grounding Prong

Properly Grounded

Three-Pronged Receptacle

Fig. 2

Grounding Lug

Make sure this is connected to a known ground.

Two-Pronged

grounded receptacle is not available, an adapter (sold separately) (Fig. 2) can be used to temporarily connect this plug to a two-contact grounded

Adapter

Receptacle

receptacle. The adapter (Fig. 2) has a rigid lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box.

! CAUTION

●In all cases, make certain the receptacle is properly grounded. If you are not sure, have a qualiﬁed electrician check the receptacle.

●This tool is for indoor use only. Do not expose to rain or use in damp locations.

●This tool must be grounded while in use to protect the operator from electric shock.

●Never remove the grounding prong from the power cord. If damaged, discontinue use of unit and contact customer service for a replacement cord.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

(When using 120 volts only)

Ampere Rating			Total length of Cord
More Than	Not More Than	25ft.	50ft.	100ft.	150ft.
0	6	18	16	16	14

6	10	18	16	14	12

10	12	16	16	14	12
12	16	14	12	Not Recommended

11

Image 11

Craftsman 137.37564 ! Caution, Three-Pronged Plug Grounding Prong Properly Grounded, Three-Pronged Receptacle, Adapter

Contents

12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model No Customer Help Line For Technical SupportSears Parts & Repair Center Operator’s ManualPAGE TABLE OF CONTENTSWARRANTY CRAFTSMAN FULL WARRANTYCutting Capacity PRODUCT SPECIFICATIONSMOTOR MITER SAWSUPPORT AND CLAMP WORK SYMBOLS! DANGER ! WARNING ! CAUTION PROHIBITIONPOWER TOOL SAFETY 12. ALWAYS WEAR EYE 27. WEAR HEARING ! DANGER7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust DUAL BEVEL COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 23.NEVER use the miter saw in areas with ﬂammable liquids or gases 25.SHUT OFF the power before servicing or adjusting the tool27.MAKE SURE the work area is clean before leaving the machine ELECTRICAL REQUIREMENTS AND SAFETY Grounding Lug Make sure this is connected to a known ground ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Three-Pronged ReceptacleBLADE INFORMATION ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES ACCESSORIESCOMBINATION SQUARE MUST BE TRUE TOOLS NEEDED FOR ASSEMBLYSuppliedNot supplied CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY SAW BLADE WRENCH FIG. E INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F Fig. DFig. H REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. GFig. K MOUNTING THE MITER SAW 90 Bevel Pointer Adjustment Fig. P ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel adjustment Fig. N, OFig. Q 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. P33.9 Right Bevel Adjustment Fig. S Fig. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W SQUARING THE FENCE FIG. UQUICK-CAM MITER TABLE LOCK OPERATION FIG POSITIVE STOP MITER ANGLE ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK ADJUSTMENT FIG OPERATION INSPECT YOUR WORKPIECE DRESS FOR SAFETYPLAN YOUR WORK USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WHEN SAW IS RUNNINGDO NOT OVERREACH Never cut freehandBODY AND HAND POSITION FIG. Y Fig. Z-2 Fig. Z-1Laser Warning Label cutting lineTO TURN SAW ON FIG. AA Fig. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw MITER CUT FIG. CCCOMPOUND CUT FIG. FF Fig. HH Fig. KK Bevel/Miter SettingsCUTTING CROWN MOULDING FIG. KK, LL Fig. MM CHANGING THE BELT FIG. MMCompound Miter Saw CROWN MOLDING CHARTMiter and Bevel Angle Settings Wall to Crown Molding Angle ! DANGER MAINTENANCELUBRICATION FIG. OO PROBLEM CAUSE TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEMVacuum or blow out dust. WEAR TROUBLESHOOTING GUIDEMODEL NO PARTS LISTPARTS LIST FOR MITER SAW - PART A 12 IN. DUAL BEVEL COMPOUND MITER SAWI.D. Description PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOX62Y Q’ty DescriptionSize Here’s what the Repair Protection Agreement* includes Sears Installation ServiceREPAIR PROTECTION AGREEMENTS Our Home Get it fixed, at your home or oursYour Home