Manuals / Craftsman / Lawn and Garden / Chainsaw Sharpener

Craftsman 137.37564 manual Positive Stop Miter Angle Adjustment Fig

Models: 137.37564

1 49

Download 49 pages 7.58 Kb

Page 27

POSITIVE STOP MITER ANGLE ADJUSTMENT (FIG. X)

POSITIVE STOP MITER ANGLE ADJUSTMENT (FIG. X)

1.Unlock the miter table by lifting up on the quick-cam miter locking lever (1).

2.While raising the positive stop locking lever (2) up, grasp the miter handle and rotate the miter table left or right to the desired angle.

3.Release the positive stop locking lever, and set the miter at the desired angle, making sure the lever snaps into place.

NOTE: The lever will only lock into place at one of the nine positive stops.

4.Once angle has been obtained, press down on the quick-cam miter locking lever (1).

Fig. X

4.Press down on the quick-cam miter locking lever (1) until it locks the miter table in place.

NOTE: The quick-cam miter locking lever should lock the table and prevent it from moving. If adjustment is needed, see next step.

QUICK-CAM MITER TABLE LOCK ADJUSTMENT (FIG. X)

1.Press down and lock the quick-cam miter table lock.

2.Turn the stop nut (3) to the left, as shown, using a 1/2 in. wrench to extend the locking arm against the base of the miter saw.

3.Test the quick-cam miter table lock to verify it locks the table into position securely.

4.Turn the lock nut (4) to the right, as shown, to lock the miter locking mechanism into place.

3		1
3	4	2

QUICK-CAM MITER TABLE LOCK OPERATION (FIG. X)

If miter angles required are NOT one of the nine positive stops noted above, the miter table can be locked at any angle between these positive stops by using the miter quick-cam table lock.

1.Unlock the miter table by lifting up on the quick-cam miter locking lever (1).

2.While holding the positive stop locking lever up, grasp the miter handle and move the miter table left or right to the desired angle.

3.Release the positive stop locking lever (2).

27

Image 27

Craftsman 137.37564 manual Positive Stop Miter Angle Adjustment Fig, Quick-Cam Miter Table Lock Adjustment Fig

Contents

12 IN. DUAL BEVEL COMPOUND MITER SAW WITH LASER TRAC Model No Customer Help Line For Technical SupportSears Parts & Repair Center Operator’s ManualPAGE TABLE OF CONTENTSWARRANTY CRAFTSMAN FULL WARRANTYCutting Capacity PRODUCT SPECIFICATIONSMOTOR MITER SAWSUPPORT AND CLAMP WORK SYMBOLS! DANGER ! WARNING ! CAUTION PROHIBITIONPOWER TOOL SAFETY 12. ALWAYS WEAR EYE 27. WEAR HEARING ! DANGERDUAL BEVEL COMPOUND MITER SAW SAFETY SPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW7. KEEP THE MOTOR AIR SLOTS CLEAN and free of chips or dust 25.SHUT OFF the power before servicing or adjusting the tool 27.MAKE SURE the work area is clean before leaving the machine23.NEVER use the miter saw in areas with ﬂammable liquids or gases ELECTRICAL REQUIREMENTS AND SAFETY Grounding Lug Make sure this is connected to a known ground ! CAUTIONThree-Pronged Plug Grounding Prong Properly Grounded Three-Pronged ReceptacleBLADE INFORMATION ACCESSORIES AND ATTACHMENTSRECOMMENDED ACCESSORIES ACCESSORIESTOOLS NEEDED FOR ASSEMBLY SuppliedNot suppliedCOMBINATION SQUARE MUST BE TRUE CARTON CONTENTS KNOW YOUR DUAL BEVEL COMPOUND MITER SAW GLOSSARY OF TERMS WOODWORKING TERMS ASSEMBLY SAW BLADE WRENCH FIG. E INSTALLING THE EXTENSION WING ASSEMBLY FIG. DINSTALLING THE SAFETY HOLD- DOWN CLAMP FIG. F Fig. DFig. H REMOVING AND INSTALLING THE BLADE Removing Blade Fig. H, I, J, KINSERTING AND REPLACING THE LASER BATTERIES FIG. G Fig. GFig. K MOUNTING THE MITER SAW 90 Bevel Pointer Adjustment Fig. P ADJUSTMENTSBEVEL STOP ADJUSTMENT 90 Bevel adjustment Fig. N, OFig. Q 45 Right Bevel Positive Stop Adjustment Fig. Q45 Left Bevel Positive Stop Adjustment Fig. R Fig. P33.9 Right Bevel Adjustment Fig. S Fig. U MITER ANGLE ADJUSTMENT FIG. V, WMITER SCALE INDICATOR FIG. W SQUARING THE FENCE FIG. UPOSITIVE STOP MITER ANGLE ADJUSTMENT FIG QUICK-CAM MITER TABLE LOCK ADJUSTMENT FIGQUICK-CAM MITER TABLE LOCK OPERATION FIG OPERATION DRESS FOR SAFETY PLAN YOUR WORKINSPECT YOUR WORKPIECE USE EXTRA CAUTION WITH LARGE OR ODD SHAPED WORKPIECES WHEN SAW IS RUNNINGDO NOT OVERREACH Never cut freehandBODY AND HAND POSITION FIG. Y Fig. Z-2 Fig. Z-1Laser Warning Label cutting lineTO TURN SAW ON FIG. AA Fig. CC BEFORE LEAVING THE SAWTo avoid injury from materials being thrown, always unplug the saw MITER CUT FIG. CCCOMPOUND CUT FIG. FF Fig. HH Bevel/Miter Settings CUTTING CROWN MOULDING FIG. KK, LLFig. KK Fig. MM CHANGING THE BELT FIG. MMCROWN MOLDING CHART Miter and Bevel Angle Settings Wall to Crown Molding AngleCompound Miter Saw ! DANGER MAINTENANCELUBRICATION FIG. OO PROBLEM CAUSE TROUBLESHOOTING GUIDETROUBLESHOOTING GUIDE - MOTOR PROBLEMVacuum or blow out dust. WEAR TROUBLESHOOTING GUIDEMODEL NO PARTS LISTPARTS LIST FOR MITER SAW - PART A 12 IN. DUAL BEVEL COMPOUND MITER SAWI.D. Description PARTS LIST FOR MITER SAW - PART B12 IN. DUAL BEVEL COMPOUND MITER SAW MODEL NOX62Y Description SizeQ’ty Sears Installation Service REPAIR PROTECTION AGREEMENTSHere’s what the Repair Protection Agreement* includes Get it fixed, at your home or ours Your HomeOur Home