Cadco XAF-135 Automatic PRE-HEATING, To View Your Cooking Parameters During the Cooking Cycle

Page 7

•AUTOMATIC PRE-HEATING

♦When you activate a memorized program with the START/STOP key, the oven will automatically preheat the cooking cavity and you will see no numbers in the display window, just the letters “PRE.”

♦Pre-heating temperature is equal to the set temperature plus approximately 20%.

♦When the oven reaches the pre-heating temperature, it gives a long tone. At this point, open the door, place the food inside the oven and close the door; your chosen program will begin cooking automatically.

•TO VIEW YOUR COOKING PARAMETERS DURING THE COOKING CYCLE:

While the oven is in its programmed cooking cycle, it is possible to view the cooking parameters. To view the different parameters (Time, Temperature), simply press the SELECT key to advance the light.

♦If you select “Time”, the display shows the remaining time.

♦If you select “Temperature”, the display will alternate between the set temperature (steady light) and the actual temperature (flashing light).

♦When the oven is in its programmed cooking cycle, you may modify the Time parameter (add minutes) while the program is in progress.

•START / STOP COOKING CYCLE

♦To start or stop the cooking cycle, press the START / STOP key.

♦At the end of the cooking cycle, the heating element(s) and fan(s) will stop running and a tone will sound for 15 seconds. The digits “0.00” will flash for 45 seconds in the display window. The original temperature remains as entered at the beginning of the cooking cycle and the START / STOP LED will remain on.

♦If during the 45 seconds of flashing digits the operator chooses to set a different time/temperature (using the or , and SELECT keys) and begin another cook cycle, the oven will then automatically begin the new cook cycle.

♦At the end of the 45 seconds, or if the cooking cycle is interrupted by pressing the START / STOP key, all the parameters previously set will be set to 0 and the START/STOP LED will be switched off.

3.2 USE OF THE “DYNAMIC” CONTROL PANEL (Models XAF-115, XAF-135, XAF-188, XAF-195)

The Dynamic control panel can work both in Manual and in Programmed modes. For each cooking cycle (both in the Manual and in the Programmed mode) the operator can set 3 cooking steps.

For each step, you enter cooking time, oven temperature, and humidity %.

MANUAL MODE

•Switching On / Switching Off

♦When the power is turned on, the light in the cooking cavity will come on and remain on while there is power to the oven. The display window will read “0.00” (this shows the time in hours and minutes).

♦15 minutes after the end of the cooking cycle (in both the Manual and the Programmed mode), or

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Digital Classic Control Panel Models Index Feet Assembly Instruction for the InstallerInstallation Preliminary Operations Check the Location of InstallationII. Instructions for the User Installation Electrical ConnectionInstructions for the Operator Select KEY Manual ModeSwitching On / Switching Off USE of Classic Control Panel Models XAF-111 & XAF-130To Enter a Program Into Memory TemperatureProgrammed Mode Start / Stop Cooking CycleTo View Your Cooking Parameters During the Cooking Cycle Automatic PRE-HEATINGTo Modify Your Cooking Parameters During the Cooking Cycle Step KEYProgrammed Mode III. Cooking Principles IV. Maintenance Reset the Safety Thermostat Replacement of the Fuse To replace the fuseRemove and Reattach the Door Optional Digital Convection Ovens Accessories VI. Cooking Guide Variables Cookies Baking TemperatureTemperature of the dough Fat content of the doughPies MuffinsBiscuits BreadOptions Oven Fried ChickenRotisserie Style Chicken MethodJus Rare Roast BeefPrime Rib roast and hold method Roast Tenderloin quick roast and serve methodLineChefTM Digital Convection Ovens VII. WarrantyWarranty Periods ALL Ovens Warranty Procedures
Top Page Image Contents