AEG 50730 manual Ing the appropriate button, Dishwasher must be switched off, Manual setting

Page 11

Operating Instructions

Adjust the water softener to the water hardness setting for your area as shown in the table.

1	It is only possible to adjust the water hardness setting when no pro-
	gramme is running. If you have accidentally started a programme (a
	LED stays on permanently), the programme must be stopped by press-
	ing the appropriate button.
0 1.	The dishwasher must be switched off.

2.Manual setting:

Open the door on the dishwasher.

3. Remove the lower basket from the dishwasher.

4. Turn the water hardness switch to 0 or 1.

5. Re-position the lower basket.

6. Electronic setting:

Press the softener and function but- tons simultaneously and keep them pressed.

7.In addition press the ON/OFF button.

8.The LED indicators for the water softener and function buttons flash.

9.Press the softener button again.

–At first the LED indicator for the water softener button will light up continuously for 5 seconds and then begin to flash.

–The number of flashes corresponds to the hardness setting.

–The sequence of flashes is repeated several times after a 5 second pause.

10.Each time you press the water-softener button the hardness setting will go up by 1.

(Exception: Hardness setting 1 follows hardness setting 5).

–If the hardness setting is changed, the LED indicator for the water- softener button will confirm the change by remaining illuminated continuously for 5 seconds and then flashing again.

–The number of flashes corresponds to the new hardness setting.

–The sequence of flashes is repeated several times after a 5 second pause.

11.Once the hardness setting is correctly adjusted, press the ON/OFF but- ton.

The hardness setting is then stored.

11

Image 11

Contents Favorit Pass them on to any subsequent owner of the appliance Tips on using the applianceDear customer Please read these user instructions carefullyContents Installation and Connection Instructions General Safety Safety InstructionsInstallation, Connection and Placing into Operation Child SafetyCorrect Use Disposal of Old Appliances DisposalEconomical and Ecological Dishwashing Disposing of the Packaging Material Appliance Features and Control Panel Ning Which fault has occurred on the dishwasherControl panel Panel Prior to using for the first timeAdjust the water softener Your areaIng the appropriate button Dishwasher must be switched offManual setting Electronic settingTurning it anticlockwise Filling with Salt for the Water SoftenerFill with dishwasher salt Remain illuminated Open the door, remove the lower BasketRinse aid can be added in one of two ways To switch off the control indicator for rinse aidRinse aid Fully open the rinse aid compartment lid Filling with rinse aidAdjusting Rinse Aid Dosing Not be washed in the dishwasher Daily UseLoading Cutlery and Dishes Loading Cutlery Two right-hand plate inserts Loading Pans, Frying Pans Large PlatesFolded over to the left To ease the loading of large itemsBaskets can be folded across one another Folded across one anotherAcross one another Two rear plate inserts in the lowerLoading Cups, Glasses and Coffee Services Raising the Upper Basket Adjusting the Height of the Upper BasketLowering the Upper Basket Fill with detergent Filling with DetergentUse of 3 in 1/ Combi Detergent Tablets General AdviceSpecial Advice Detergent tablets Concentrated DetergentSoiling Selecting the Wash Programme Programme TableOpen the door carefully Start the wash programmeInterrupting or ending the wash programme WasherPause function Setting or changing the delay start timerSetting the delay start timer Changing the delay start timerEmptying the Dishwasher Care and CleaningSwitching Off the Dishwasher Sive cleanersCleaning the Filter What to do, if Fault warnings are displayedDishes are wet and dull There are problems operating the dishwasherWash results are unsatisfactory Dishes are still dirtyThere are dried water drops on the glasses and dishes Technical DataDecrease rinse aid dosing Upper basket Lower basket with cutlery basket Sample loading arrangementsFree-Standing Appliances Installing the DishwasherSee enclosed installation instructions Built-Under DishwasherWork surface must be re-mounted Plinth on free-standing appliances is not adjustableConnect the inlet hose Connecting the DishwasherWater Connection Permitted water pressurePlease take care when installing the water inlet hose Water inlet hose with safety valveWater drain Appliance is automatically pumped out Leak Prevention SystemChanging a fuse Electrical ConnectionConnections Guarantee Conditions Calls may be recorded for training purposes 08705 929Customer Care AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG