Lincoln Guide to Resetting Your Impinger Oven and Replacing Key Components

Page 18

FUSE HOLDER - REPLACEMENT

1.Shut off power at main breaker.

2.Remove control box cover and front panel.

3.Remove wires from fuse holder and mark for reassembly.

4.Remove mounting screws or mounting nut on fuse holder. Push fuse holder out.

5.Reassemble in reverse order.

THERMOSTAT, CONTROL BOX HI-LIMIT - REPLACEMENT

1.Shut off power at main breaker.

2.Remove control box cover and front panel.

3.Remove wires from thermostat and mark for reassembly.

4.Remove mounting screws and nuts and remove thermostat.

5.Reassemble in reverse order.

NOTE: Push reset button on new thermostat.

COOLING FAN, CONTROL BOX

1.Shut off power at main breaker.

2.Remove control panel top and front cover.

3.Remove four (4) screws from the fan frame.

4.Disconnect cord and plug and remove fan.

5.Reassemble in reverse order.

THERMOSTAT, COOLING FAN

1.Shut off power at main breaker.

2.Remove control panel top and front cover.

3.Remove lead wires and mark for reassembly.

4.Remove two (2) screws and remove thermostat.

5.Reassemble in reverse order.

BURNER BLOWER MOTOR - REPLACEMENT

1.Shut off power at main breaker.

2.Remove control panel top and front cover.

3.Unplug motor connector.

4.Remove three (3) screws from blower tube at burner housing.

5.Remove air shutter assembly from old motor for installation on new motor assembly.

6.Reassemble in reverse order and check system operation.

NOTE: Check air shutter at approximately 1/2 open and adjust to get a blue flame with an occasional tip of yellow under high flame. A view port in the burner assembly should be used to observe flame.

HIGH LIMIT THERMOSTAT - REPLACEMENT

1.Remove control panel top and front cover.

2.Remove conveyor and bottom finger assembly.

3.Remove capillary bulb from bracket in oven chamber and pull through tube into control box.

4.Remove two (2) wires from thermostat, note wire numbers and location for reinstallation.

5.Remove mounting nut and remove thermostat.

6.Reassemble in reverse order making sure capillary tube is placed securely in the bracket. NOTE: Depress reset button to insure thermostat is set for operation.

18

Impinger II – Advantage Service Manual - Domestic

Image 18
Contents Impinger Conveyor Ovens Table of Contents Sequence of Operations Impinger II AdvantageControl BOX Auto Cool Down Heater CircuitSchematic 1116-000-A, 1117-000-A Schematic 1130-000-A / 1131-000-A Schematic 1132-000-A / 1133-000-A Natural GAS Troubleshooting Guide / GAS OvensPhase LP GASPage With Power on and Thermocouple Leads Attached to the Temperature ControlPage Page Three Phase Troubleshooting Guide / Electric OvensSingle Phase Refer to Proper Schematic for Identified ComponentsWith Power on and Thermocouple Leads Attached to the TemperaturePage Page MOTOR, Main FAN REMOVAL, INSTALLATION, and AdjustmentON/OFF Switch Replacement FAN, MainBurner Blower Motor Replacement Fuse Holder ReplacementTHERMOSTAT, Control BOX HI-LIMIT Replacement High Limit Thermostat ReplacementThermocouple Measurement Chart Burner Transformer ReplacementThermocouple Replacement InformationTemperature Control Potentiometer Replacement Electronic Temperature Control Board ReplacementElectronic Temperature Control Board Calibration Heat Light ReplacementMain Burner Orifice Replacement Temperature Regulation Valve ReplacementHOT Surface Ignitor Replacement Conveyor Control Potentiometer ReplacementConveyor Control Board Calibration Conveyor Control Board ReplacementConveyor Drive Motor Replacement Circuit BreakerTemperature Display Replacement Hall Effect Sensor ReplacementTemperature Display Transformer Replacement Calibration of Temperature DisplayHeating Element Replacement BEARING, ConveyorThis page intentionally left blank Parts / General Letter Part Number DescriptionBlow UP / General Parts / Control BOX 1116-000-A, 1117-000-A Blow UP / Control BOX 1116-000-A, 1117-000-A Parts / Control BOX 1130-000-A Thru 1133-000-A Blow UP / Control BOX 1130-000-A Thru 1133-000-A Parts / Conveyor & Door Blow UP / Conveyor & Door Parts / Oven Back Assembly Blow UP / Oven Back Assembly