Merco Savory RT-2VSHO Gear Motor, Drive Chain, Drive Motor Sprocket, Rear Conveyor Shaft Sprocket

Page 3

H – GEAR MOTOR

1.With outer case removed, disconnect motor leads from on/off switch and terminal block and cut wire ties at floor panel.

2.Remove the 2 retaining bolts from the underside of the unit.

3.Remove the drive chain and lift out motor.

4.Separate motor from motor mounting bracket by removing the 4 slotted screws on the bracket.

5.Using a 1/16” allen wrench, remove the drive sprocket from the motor shaft.

6.Attach new gear motor to motor mounting bracket.

7.Install drive sprocket on motor shaft making sure the Allen screw rests on the flat of the shaft. Do not tighten set screw.

8.Install new motor with bracket attached. DO NOT tighten remaining bolts.

9.Replace drive chain over sprockets.

10.Slide motor to right until drive chain is taut. There should be approximately ¼” play in the drive chain.

11.Check drive chain alignment. Tighten drive sprocket set screws.

12.Reattach motor leads to on/off switch and conveyor speed control. (Refer to appropriate wiring diagram.)

I – DRIVE CHAIN

1.With outer case removed, loosen the two motor mounting bracket retaining bolts on underside of unit, but DO NOT remove.

2.Slide motor to the left to loosen drive chain tension.

3.Remove drive chain.

4.Install new chain over sprockets with open looped side of chain facing out.

5.Slide motor to right to tighten drive chain tension. There should be approximately ¼” play in the drive chain.

6.Check for proper drive chain alignment (See figures 6 and 7).

7.Tighten motor mounting bracket retaining bolts on underside of unit.

J – DRIVE (MOTOR) SPROCKET

1.With outer case removed and drive chain removed, loosen the set screw on sprocket with a ¼” allen wrench and remove sprocket.

2.Install new sprocket on motor shaft making sure allen screw rests on the flat of the shaft.

3.Replace drive chain.

K – REAR (CONVEYOR) SHAFT SPROCKET

1.With outer case removed and drive chain removed, loosen the two set screws on sprocket with a 1/16” allen wrench and remove sprocket.

2.Install new sprocket on conveyor shaft aligning the two set screws with the holes on the shaft.

3.Replace drive chain.

RT-2VSE/VSHO Service Manual

3

Image 3
Contents RT-2VSE & RT-2VSHO Toaster Parts Replacement Rear Conveyor Shaft Sprocket Gear MotorDrive Chain Drive Motor SprocketConveyor Chain Front & Rear Shaft Bearings Problem Possible Causes Suggested Remedies Problem Possible Causes Suggested Remedies RT-2VSE Schematic RT-2VSHO Schematic This page intentionally left blank Letter Description Parts ListExploded View

RT-2VSHO, RT-2VSE specifications

The Merco Savory RT-2VSHO and RT-2VSE are state-of-the-art heated holding cabinets designed to elevate foodservice operations. These advanced equipment solutions are tailored to meet the demands of high-volume kitchens, ensuring that food is held at optimal temperatures while preserving quality and taste.

One of the main features of the RT-2VSHO and RT-2VSE is their exceptional temperature control. Equipped with precise digital thermostats, these cabinets allow operators to set and maintain specific temperature ranges, ensuring that food stays safe for consumption. The intuitive digital display provides real-time feedback on internal conditions, enabling users to monitor temperatures at a glance.

The design of the Merco Savory cabinets is user-focused. The RT-2VSHO model, featuring glass doors, allows for visibility of food items without opening the cabinet, reducing temperature fluctuations and energy consumption. On the other hand, the RT-2VSE model comes with solid doors, providing additional insulation and energy efficiency.

Both models boast robust construction and superior insulation. The stainless-steel exterior not only enhances durability but also simplifies cleaning and maintenance. With a fully insulated cavity, these cabinets minimize heat loss, contributing to energy savings and maintaining consistent temperatures.

Another notable characteristic is the cabinets' flexibility and capacity. With adjustable shelving, operators can customize the interior space to accommodate various food items, from trays of steaming dishes to pre-packaged meals. The RT-2VSHO and RT-2VSE provide ample storage, making them ideal for busy kitchens, catering operations, or buffets.

The technology integrated into these holding cabinets includes advanced heating elements that evenly distribute heat throughout the interior, ensuring that all food items are held at safe and desirable temperatures. Moreover, both models are designed with easy-to-use controls, making them accessible for staff at all skill levels.

For operational efficiency, the Merco Savory RT-2VSHO and RT-2VSE models are also equipped with features such as lightweight, heavy-duty casters for mobility, allowing kitchen staff to reposition them as needed.

In summary, the Merco Savory RT-2VSHO and RT-2VSE holding cabinets are exemplary solutions for any professional kitchen looking to maintain food quality while ensuring safety standards. With their advanced temperature control, robust construction, and user-friendly features, these cabinets stand out as essential tools for culinary success.