Maytag W10240116A Add Rinse Aid, Select a Cycle cycles vary by model, Start or Resume a Cycle

STEP 2

Add Detergent
NOTE: If you do not plan	A
to run a wash cycle soon,
run a rinse cycle. Do not	Hard Water	Hard Water
	Soft Water
use detergent.		Soft Water
	B	C
■ Use automatic
		PRE-
	MAIN WASH	WASH
dishwasher detergent

NOTE: For most water conditions, the factory setting of 2 will give good results. If you have hard water or notice rings or spots, try a higher setting. Turn the arrow adjuster inside the dispenser by either using your fingers or inserting a flat-blade screwdriver into the center of the arrow and turning.

	-- 6		5		4
	-
max	fill					3
							2
-							1
-
-							-
	-
	-			-		-
	-	- -	-

only. Add powder,
liquid or tablet
detergent just before
starting a cycle.	A. Cover latch
■ Fresh automatic	B. Main Wash section
dishwasher detergent	C. Pre-Wash section
results in better
cleaning. Store tightly closed detergent container in a cool, dry
place.

■The amount of detergent to use depends on:

How much soil remains on the items - Heavily soiled loads require more detergent.

The hardness of the water - If you use too little in hard water, dishes won't be clean. If you use too much in soft water, glassware will etch.

Soft to Medium Water (0-6 grains per U.S. gallon) [typical water softener water and some city water]

Medium to Hard Water (7-12 grains per U.S. gallon) [well water and some city water]

■Depending on your water hardness, fill the Main Wash section of the dispenser as shown. Fill the Pre-Wash section to the level shown, if needed.

NOTE: Fill amounts shown	Hard Water
are for standard powdered
	Soft Water	Hard Water
detergent. Follow		Soft Water
instructions on the package	Main Wash	Pre-Wash
when using other dishwasher
detergent.

Add Rinse Aid

Your dishwasher is designed to use rinse aid for good

drying performance. Without rinse aid your dishes and Full dishwasher interior will have excessive moisture. The

heat dry option will not perform as well without rinse aid.

■Rinse aid keeps water from forming droplets that can

dry as spots or streaks. It also improves drying by	Add
allowing water to drain off of the dishes after the final
rinse.

■Rinse aid helps to reduce excess moisture on the dish racks and interior of your dishwasher.

■Check the rinse aid indicator. Add rinse aid when indicator drops to “Refill” level.

■To add rinse aid, turn the dispenser

cap counterclockwise and lift off.	USE RINSE AID FOR	Full
	BETTER DRYING
Pour rinse aid into the opening until
	Lock
the indicator window looks full.
Replace the dispenser cap and turn
clockwise. Make sure cap is fully	Open	Add
locked.

¹⁄₄ turn to lock

STEP 3

Select a Cycle (cycles vary by model)

See “Cycle and Option Descriptions” charts in the following section.

Heavier cycles and options affect cycle length. Some cycles and options will take up to 3¹⁄₂ hours to complete.

Select Options (options vary by model)

See “Cycle and Option Descriptions” charts in the following section.

You can customize your cycles by pressing the options desired and press Start/Resume.

STEP 4

Start or Resume a Cycle

NOTE: For portable models, see the “Dishwasher Features” section for instructions on how to connect the water and electrical supply.

■Run hot water at the sink nearest your dishwasher until the water is hot. Turn off water.

■Push door firmly closed. The door latches

automatically. Select the wash cycle and options desired and press START/RESUME OR press START/ RESUME to repeat the same cycle and options as in the previous wash cycle.

■You can add an item anytime before the main wash starts. Open the door slowly and add the item. Close the door firmly. Press the START/RESUME button, the cycle resumes automatically at the point of interruption.

For fully integrated models (controls on top of console)

■Select the wash cycle and options desired.

■Press the START/RESUME button once and close the door. After a brief pause, the cycle will begin. The door must be closed within 3 seconds after pushing START/RESUME or the lights will flash, and the dishwasher will not begin. Press the START/RESUME button again and shut the door within

3 seconds.

You can add an item anytime before the main wash starts. Open the door slowly and add the item. Press the START/RESUME then close the door.

4