Maytag AOCS3040, AOES3030 manual Service Information, Quick Test Procedure, Pad Response

Page 35

Testing Procedures

!WARNING

To avoid the risk of electric shock, personal injury or death, disconnect power before servicing, unless testing requires it.

Service Information

The ERC operates in conjunction with a separate relay/ power supply circuit board, and oven temperature sensor(s) to control all bake, broil, convection, and self clean functions.

The ERC is connected through to a function panel to control minute timer, clock, stop time, oven light, panel light, cancel, bake, cook time, broil, convection bake, convection, convection broil, and clean. Slew pads are used to set times and temperatures.

The mylar control panel provides direct input to the ERC to control all functions.

The ERC display consists of two digital readouts which displays all timing functions, and all temperature functions.

The relay/power supply circuit board consists of relays for convection fan, oven light, convection element, bake, broil, door lock, and double line break operations controlled by the ERC, and a step down transformer with two secondary windings which convert 120 VAC input to filament voltage to power the ERC display.

The oven temperature sensor is mounted in the oven cavity and connected to the J4 connector on the rear of the ERC. As the oven temperature increases, the sensor resistance also increases. The ERC converts this resistance change to a corresponding temperature readout and to cycle the relay(s) to maintain the desired temperature setting.

The ERC is also capable of sensing certain failure conditions which can occur in the oven temperature sensor(s), the self clean latch switch(es) the adaptor board or the ERC itself. If the ERC senses a failure, power will be removed from the relays, an alarm will sound and a failure code will be displayed.

Each major component of the Electronic Range Control system is serviced as a separate part. However, each component and related wire harness must be tested prior to replacing an individual component.

Quick Test Procedure

“Quick Test” Mode for Electronic Range Control Follow procedure below to use the quick test mode. Entries must be made within 32 seconds of each other or the control will exit the quick test mode. The quick test mode cannot be reactivated until power is disconnected from oven, and must be accessed within 5 minutes of powering up.

NOTE: To enter quick test mode, this must be the first

key pad entered after power is applied.

1.Apply power to oven press and hold COOK TIME pad for 5 seconds.

2.Display will read the following:

Pad

Response

CLEAN

Double Line Break (DLB) on and

 

door lock status code displayed

BAKE

DLB and Bake on

CONV. BAKE

DLB, Bake and Conv Fan on

CONVECTION

DLB, Conv. Element and Fan on

BROIL

DLB and Broil on

CONV. BROIL

DLB, Broil and Conv. Fan on

STOP TIME

Beeper on

COOK TIME

Displays manufacturer code and

 

sensor readings “000”=open sensor

TIMER

Displays dashes

CLOCK

All display segments illuminated

OVEN LIGHT

Oven light on

CANCEL

Exit Quicktest

SLEW

Sequences through display

 

segments

©2003 Maytag Appliances Company

16021875 Rev. 0

B—7

Image 35
Contents Service Table of Contents Maytag Appliances Company Important Information All Appliances Recognize this symbol as a safety precautionSelf-Cleaning OvenCooking Guide General InformationOven Operation Convection Broiling Rack Oven Rack PlacementConvection Pan Placement Pan PlacementTilting Control Panel Removing Oven DoorReplacing Oven Door Replacing Oven LightCleaning Oven Parts Cleaning Materials General Directions Care and CleaningIllustration Component Test Procedure Results Component Testing InformationERC mylar touch system Selecting Options Field Selectable OptionsClock Time Format 12 or 24 hour format Clock Time Base 60 or 50 Hz input line frequencyElement Conditions Oven Temperature Sensor Testing ProceduresOven Door Switch Oven High Limit/Fan SwitchAuto Latch Motor Convection Element TestingBroil Element Testing Bake Element TestingERC/P.C. Board Oven High Limit/Fan Control SwitchRemoving and Replacing Oven Control PanelBake Element Automatic Oven Door Latch AssemblyDoor Plunger Light Switch Oven SensorOven Door Removal Frameless Door DisassemblyOven Light Bulb/Oven Light Socket Oven Tank RemovalOven Door Hinge Vent Assembly/Smoke EliminatorOuter Trim Assembly Door Assembly 16021875 Rev Appendix a Line Voltage Requirements Oven DImensionsPackaging Material Oven LocationOption Connecting WiringInstallation Instructions Centerline of cabinet Top cutout AOES3030 or AOCS3040 Wall Oven Stacked InstallationCabinet Tilt Loosen screw Pivot screw AOES3030 or AOCS3040 Wall Oven Installed Side-by-SideThis page intentionally left blank for notes Appendix B Special Oven Control Functions Programming Instructions-ERC for AOES3030Electronic Oven Control Options Quick Reference Instructions Broiling Delayed BakeBake Timed BakeDelayed Self-Cleaning Interrupt Self-Cleaning CycleService Tones and Codes Adjusting Oven TemperaturePad Response Service InformationQuick Test Procedure Transformer/Relay Module Function Switch Connection Check ProcedureTemperature Calibration Offset ERC Warnings and Failure CodesDoor Lock Relay-K3 Oven Light Relay-K10Display Filament Voltage This page intentionally left blank for notes Appendix C Programming Instructions-ERC for AOCS3040 Programming Instructions-ERC for AOCS3040 Self-CleaningConvection Delayed Bake or Convection BakeBake and Convection Bake Timed Bake or Convection BakeDehydration Tips Delayed ConvectionBroil and Convection Broil Convection DehydrationPres Oven Cancel pad Canceling Self-Cleaning CycleConvection DLB, Conv. Element and Fan on Connection, test control panel continuity Convection Fan Relay-K1 Convection Element Relay-K2

AOCS3040, AOES3030 specifications

The Maytag AOES3030 and AOCS3040 are two standout models in the Maytag lineup, offering robust performance and thoughtful design, making them ideal for modern households. These models reflect Maytag's commitment to durability, convenience, and user-friendly features.

The AOES3030 is known for its spaciousness, featuring a large oven capacity that allows home cooks to prepare multiple dishes at once, making it perfect for family gatherings or meal prepping. Its cooking surface is crafted with high-quality materials, ensuring durability and ease of cleaning. One of the key technologies incorporated into the AOES3030 is the Precision Cooking System. This innovation optimizes the cooking process by utilizing advanced sensors that monitor and adjust cooking times and temperatures, ensuring perfectly cooked meals every time.

In contrast, the AOCS3040 offers a versatile cooking solution with its unique range of features. The AOCS3040 is equipped with a powerful induction cooktop that allows for rapid heating and precise temperature control. Induction cooking is known for its energy efficiency as it directly heats pots and pans without heating the surrounding area, thus minimizing energy waste. Furthermore, the AOCS3040 includes a built-in oven with a self-cleaning feature, taking the hassle out of maintaining a pristine cooking environment.

Both models showcase Maytag's commitment to reliable performance, incorporating heavy-duty components that are built to last. They are designed with user-friendly controls that are intuitive, enhancing the overall cooking experience. Another noteworthy aspect of both models is their sleek, modern design, which includes stainless steel finishes that can seamlessly blend into any kitchen decor.

Safety features are also a priority, with each model incorporating child locks and automatic shut-off options, making them suitable for households with children. With their blend of innovative technologies, user-focused features, and robust construction, the Maytag AOES3030 and AOCS3040 set a high standard for kitchen appliances, offering both style and function for the modern chef. These models demonstrate that Maytag continues to innovate while honoring the brand's legacy of reliability.