Bunn LCC-2 service manual Decaffeinated Coffee Right Dispenser Flow Rate Calibration

Page 25

Field Calibration of the Concentrate Pumps & Dispenser Flow Rates

(Continued)

5.Place a 1500 to 2000 ml graduated container under Left Dispense Tip.

6.Press & Hold the Regular dispense switch. The dispenser will display a 20 second count down timer and then stop dispensing automatically. Release the dispense switch.

7.Keep the graduated container under dispense tip until all the water stops dripping.

8.Measure the volume of water collected in the graduated container.

The acceptable range for the volume of water collected is .95 - 1.12 liters

9.If the amount of water collected is not within the acceptable range, empty the graduated container and repeat STEPS 5 – 8.

10.If the amount collected is still not within range, inspect the dispense valves, tubing and mix chamber for lime, kinks or other obstructions.

11.When satisfied with the volume of water collected, press the MENU switch. The current Water Calibration volume “C3 XX” will be displayed.

12.Use the (-) / (+) keys to adjust number displayed to the amount measured in STEP 8.

Decaffeinated Coffee - Right Dispenser Flow Rate Calibration

Depress the MENU switch to display the Decaffeinated Coffee Flow Rate calibration menu “C4 run”. Repeat STEPS 3 – 12 above for the right side “Decaf” pump.

Field Calibrating the Empty Product Warning

The dispenser will automatically turn on the Regular or Decaf “REFILL LED”, see Operating Controls and Interface, when the corresponding container is Empty. The Refill message is triggered when the conductance sensor read- ing drops below the minimum setting. The factory set minimum is 600 and should be correct for most locations. However, in some areas the hardness of the local water supply may effect this reading. If the Refill message doesn’t come on when the container is empty or the message comes on too early and there is still concentrate left in the container, use the following procedure to find the correct Empty Product Threshold.

Calibrating The Empty Product Threshold

1.Open the dispenser door to access the digital programming module with LED display and set the Function Switch to the “Rinse” position. Leave the door open to view the LED display.

2.Place a large container under the dispenser tip, then activate and hold the Regular Coffee dispense switch.

3.Hold the dispense switch long enough to rinse all the concentrate out of the mix chamber and for the Con- ductance reading to stabilize and stop dropping.

4.Record the nominal Conductance value displayed. (NOTE: It is typical for this value to fluctuate (+/- 25) points about the nominal value.) This is the conductance reading of the water in your area.

5.Repeat steps 2, 3 & 4 for the Decaf Coffee dispenser.

6.Add 100 points to the larger of the Regular or Decaf conductance value. This is the new Empty Product threshold value for your dispenser.

7.Enter this new value into the Empty Product Alarm threshold position “P8 XXX”, see Programming the Dispenser.

25

39288 072707

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Phone 217 529-6601 FAX 217 LCC-2 LPBUNN-O-MATIC Commercial Product Warranty Contents 00656.0001 00986.0002 00824.0002 37881.0000 11646.0002 User Notices40054.0000 Electrical Requirements IntroductionPlumbing Requirements Plumbing HOOK-UP Early Models Initial SET-UPPlumbing HOOK-UP Late Models Turn on the water supply and check for leaksOperating Controls and Interface Electrical HOOK-UP39288 Installing the Pump Tubing Installing Pump TubingInitial Fill & Heat Disabled None Rinse Alarm FeatureServe product 1 8 Display Mode DescriptionProgramming the Dispenser LCD Display0 0 Programming the Dispenser Display Mode6 0 LC xTank Temperature Default = 180F 82C Range = 120 200F 49 93C Program Mode DescriptionProgramming the Dispenser ~5.5CLCD Display Program Mode Description Programming the Dispenser Program ModeLC 0 x Program Function  DESCRIPTIONDraining the HOT Water Tank Priming the Concentrate LinesOperating the Dispenser General Cleaning and Sanitizing Procedures Daily Rinsing Cleaning & Preventative MaintenanceReplacing the Pump Tubing Preventive MaintenanceC1 2 C1 r u nC2 r u n C2 2C5 0 6 C4 1C5 CHL C6 2 0Error Codes Troubleshooting GuideError EC 0 0DESCRIPTION/TROUBLESHOOTING Troubleshooting Guide Error Codes0 1 Decaffeinated Coffee Right Concentrate Pump Calibration Decaffeinated Coffee Right Dispenser Flow Rate Calibration J4-5 LCC-2 LP Bunn Chilled
Related manuals
Manual 34 pages 56.59 Kb Manual 36 pages 62.09 Kb

LCC-2 specifications

The Bunn LCC-2, LCA-2 PC, and LCA-2A are high-performance commercial coffee brewers designed to meet the demands of busy coffee shops, restaurants, and other food service establishments. These machines are known for their efficiency, durability, and advanced brewing technologies, making them popular choices in the industry.

Starting with the Bunn LCC-2, this brewer is recognized for its compact design and ease of use. It has a brewing capacity of up to 3.8 gallons per hour, ensuring that coffee is ready quickly during peak hours. The LCC-2 uses a pour-over brewing method, which means that water is heated to the ideal brewing temperature and then poured over coffee grounds for optimal extraction. One of its standout features is the digital temperature control, which allows operators to adjust brewing temperatures easily for different coffee types. Additionally, the Bunn LCC-2 features a stainless steel construction that enhances durability and provides a sleek look for any commercial kitchen.

Moving on to the Bunn LCA-2 PC, this model includes programmable capabilities, making it perfect for establishments that require consistency and convenience. The LCA-2 PC allows users to preset brewing schedules and customize brew cycles, ensuring that each pot of coffee meets specific flavor profiles. This model is designed with a large-capacity brewing system that can produce up to 7.5 gallons of coffee per hour, making it an ideal choice for high-demand environments. It also boasts a built-in hot water faucet, which provides instant hot water for other beverages or culinary applications. The LCA-2 PC's advanced brewing automation helps maintain optimal brew quality while minimizing waste.

Lastly, the Bunn LCA-2A is an advanced version that focuses on automation and efficiency. This brewer features a state-of-the-art digital brew timer, which allows precise control over brew times, leading to consistent flavor extraction. The LCA-2A also integrates with Bunn’s patented brewWISE technology, which tracks brew recipes and monitors performance. The intuitive interface allows for easy operation, even for staff who may be less experienced with coffee brewing. With a capacity of up to 4 gallons per hour and a durable stainless steel frame, the LCA-2A ensures longevity while delivering exceptional coffee.

In summary, the Bunn LCC-2, LCA-2 PC, and LCA-2A represent the pinnacle of commercial coffee brewing technology. Their unique features, including programmable settings, large brewing capacities, and durable constructions, cater to the diverse needs of the food service industry. Each model emphasizes convenience, flexibility, and quality, making them invaluable assets in any professional coffee environment.
Top Page Image Contents