Bunn TB6Q Disconnect the control thermostat wires, Adjust the control thermostat as required

Page 11

SERVICE (cont.)

CONTROL THERMOSTAT (cont.)

source. The indication must be:

a)120 volts ac for two wire 120 volt models.

b)200 to 230 volts ac for two wire 200 volt or 230 volt models.

8.Disconnect the brewer from the power source.

If voltage is present as described, reinstall the capillary tube into the tank to the line 4.5" above the bulb, the control thermostat is operating properly.

If voltage is not present as described, replace the thermostat.

Removal and Replacement:

1.Disconnect the control thermostat wires.

2.Remove the thermostat capillary bulb by firmly pulling-up on the capillary at the tank lid. This will disengage the grommet from the tank lid.

3.Remove the one #6-32 screw securing the control thermostat to the component bracket inside the hood.

4.Slide the grommet to the line 4.5" above the bulb on the new capillary tube.

5.Insert the capillary bulb through the hole in the tank lid and press the grommet firmly and evenly so that the groove in the grommet fits into the tank lid.

6.Carefully bend the capillary tube so that the tube and bulb inside the tank are in the vertical posi- tion.

NOTE - The capillary tube must be clear of any electri- cal termination and not kinked.

7.Using one #6-32 screw, secure the control thermo- stat to the component bracket inside the hood.

8.Adjust the control thermostat as required.

FIG. 11-1 CONTROL THERMOSTAT TERMINALS

FIG. 11-2 REPLACEMENT CONTROL THERMOSTAT

Page 11

41722 070209

 

Image 11
Contents Phone 217 529-6601 FAX 217 TB3/TB6 SeriesBUNN-O-MATIC Commercial Product Warranty Contents To the brewer Probable Cause RemedyBrew cycle will not start No water Control Thermostat Tank Heater ProblemBrew cycle will not start Water is not hot Probable CauseLeaks Inconsistent beverage levelSurfaces can initiate corrosive Reactions resulting in seriousBeverage overflows dispenser Refer to Service Timer for test- ing proceduresSpitting or excessive steaming Dripping from sprayhead Plumbing Lines Water Supply Dry coffee grounds remainFunnel Brewer is making unusal noises Cont Tank heater Problem Probable Cause RemedyBrewer is making unusal noises Tank Heater Location Control thermostat is located in the hood Component AccessControl Thermostat Adjust the control thermostat as required Disconnect the control thermostat wiresLimit Thermostat Remove all wires from limit thermostat termi- nals1680W-120V 1680W-100V 1680W-230V 29.0 33.7 Disconnect the brewer from the power supplyTank Heater Orange light Lighted ON/OFF Switch TB3/TB3QRefer to -2 when reconnecting the wires If continuity is present as described, replace the wires Switch is located on the front control panelThrough four when the switch is in the oposite Position Switch37080.0001to T. Stat Start SwitchesInlet Valves BREW/DILUTION Timer TB3 & TB6 Triacs TH-1/MV-1 Brew solenoid TH-2/MV-2 Dilution solenoid BREW/DILUTION Timer TriacsWhite Red Neutral L2 Digital Brew Timer TB3Q & TB6QTerminals ½ batch connector Triacs MV-2 Brew solenoid output MV-1 Line Digital Timer TriacsVolts AC Wire Single Phase Schematic Wiring Diagram TB3QSchematic Wiring Diagram TB3, TB3B, TB3-LP Schematic Wiring Diagram TB3Q Schematic Wiring Diagram TB3Q W/SWEETENER & Empty BAG Detect Schematic Wiring Diagram TB6 Schematic Wiring Diagram TB6Q
Related manuals
Manual 11 pages 51.02 Kb

TB6Q, TB6 specifications

The Bunn TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers are a popular series of commercial machines designed for high efficiency and optimal performance in busy environments such as cafes, restaurants, and offices. These machines are crafted with a focus on quality, dependability, and advanced brewing technology to deliver a superior coffee experience.

One of the standout features across the Bunn TB series is the ability to brew large quantities of coffee quickly. The TB6Q, for instance, can brew up to 6 gallons of coffee per hour. This high volume brewing capability ensures that establishments can keep up with demand, especially during peak hours. Additionally, the machines come with a unique design that incorporates a pre-infusion feature, allowing for the coffee grounds to be evenly saturated before brewing begins, enhancing the flavor extraction process.

The TB3-LP model is designed for low-profile applications where counter space may be limited. Despite its compact design, it still offers impressive performance, brewing up to 3.8 gallons per hour. The low-profile feature makes it an ideal choice for settings that require efficiency and space optimization without compromising on the quality of the brew.

Another notable member of the series, the TB3Q and TB3Q-LP, feature a quick brew ratio, allowing users to brew up to 3 gallons of coffee in just a few minutes. These models are equipped with easy-to-use controls for simplified operation, making them perfect for staff training and user accessibility.

All models in the TB series include a hot water faucet, allowing users to dispense hot water for tea or other hot beverages quickly. This versatility adds significant value, especially in multi-beverage settings.

Regarding durability, the Bunn TB series is constructed with high-quality materials, ensuring longevity and reliability. The machines also feature internal components that are easy to access for maintenance, thus reducing downtime and improving the overall efficiency of the machine.

In terms of technology, these brewers often incorporate advanced diagnostics to promptly identify service needs or issues. The machines come with a precise brewing temperature control system that ensures each cup is brewed at the optimal temperature for maximum flavor extraction.

Overall, Bunn's TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers represent the culmination of advanced brewing technology and practical design for commercial coffee solutions. Their efficiency, quality, and ease of use make them a staple in many establishments, solidifying Bunn's reputation as a leader in the coffee brewing industry.