Bunn TB6Q manual Tank Heater, Disconnect the brewer from the power supply

Page 13

SERVICE (cont.)

TANK HEATER

FIG. 13-1 TANK HEATER

Location:

The tank heater is located inside the tank and secured to the tank lid.

Test Procedures:

1.Disconnect the brewer from the power supply.

2.Turn on thermostat. Check the voltage across the black and white wires on 120 volt models or the black and red wires for 200 volt models and 230 volt models with a voltmeter. Connect the brewer to the power source. The indication must be:

a)120 volts ac for two wire 120 volt 20 amp models .

b)200 to 230 volts ac for two wire 200 or 230 volt models.

3.Disconnect the brewer from the power source.

If voltage is present as described, proceed to #4

If voltage is not present as described, refer to the Wir- ing Diagrams and check wiring harness.

4.Disconnect the wires from the tank heater termi- nals.

5.Check resistance value across tank heater terminals and compare to chart.

If resistance is present as described, reconnect the wires, the tank heater is ok.

HEATER

RESISTANCE

1680W-120V

7.9

- 9.2

1680W-100V

5.5

-6.4

1680W-230V

29.0

-33.7

TERMINAL TO SHEATH - INFINITE (OPEN)

If resistance is not present as described, replace the tank heater.

NOTE- If any resistance is read between sheath and either terminal, remove and inspect heater for cracks in the sheath.

Removal and Replacement:

1.Disconnect the brewer from the power supply.

2.Disconnect the water supply from the brewer.

3.Disconnect the wires from the limit thermostat.

4.Disconnect the wires from the tank heater termi- nals.

5.Remove sprayhead and the hex nut securing the sprayhead tube to the hood. Set aside for reas- sembly.

6.Remove the six #10 screws securing the tank lid to the tank.

7.Remove the tank lid with limit thermostat, spray- head tube and tank heater.

8Remove the two hex nuts securing the tank heater to the tank lid. Remove tank heater with gaskets

and discard.

9.Install new tank heater with gaskets on the tank lid and secure with two hex nuts.

10.Install tank lid with limit thermostat, sprayhead tube and tank heater using six #10 screws.

11.Secure sprayhead tube to hood using hex nut removed in step 4.

12.Install sprayhead.

15.Reconnect the wires to the limit thermostat and tank heater.

16.Reconnect the water and power supply.

Page 13

41722 070209

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Phone 217 529-6601 FAX 217 TB3/TB6 SeriesBUNN-O-MATIC Commercial Product Warranty Contents Brew cycle will not start No water Probable Cause RemedyTo the brewer Brew cycle will not start Water is not hot ProblemProbable Cause Control Thermostat Tank HeaterSurfaces can initiate corrosive Inconsistent beverage levelReactions resulting in serious LeaksSpitting or excessive steaming Dripping from sprayhead Refer to Service Timer for test- ing proceduresBeverage overflows dispenser Funnel Brewer is making unusal noises Dry coffee grounds remainPlumbing Lines Water Supply Brewer is making unusal noises Tank Heater Problem Probable Cause RemedyCont Tank heater Control Thermostat Component AccessLocation Control thermostat is located in the hood Adjust the control thermostat as required Disconnect the control thermostat wiresLimit Thermostat Remove all wires from limit thermostat termi- nalsTank Heater Disconnect the brewer from the power supply1680W-120V 1680W-100V 1680W-230V 29.0 33.7 Refer to -2 when reconnecting the wires Lighted ON/OFF Switch TB3/TB3QOrange light Through four when the switch is in the oposite Position Switch is located on the front control panelSwitch If continuity is present as described, replace the wires37080.0001to T. Stat Start SwitchesInlet Valves BREW/DILUTION Timer TB3 & TB6 Triacs TH-1/MV-1 Brew solenoid TH-2/MV-2 Dilution solenoid BREW/DILUTION Timer TriacsTerminals ½ batch connector Digital Brew Timer TB3Q & TB6QWhite Red Neutral L2 Triacs MV-2 Brew solenoid output MV-1 Line Digital Timer TriacsVolts AC Wire Single Phase Schematic Wiring Diagram TB3QSchematic Wiring Diagram TB3, TB3B, TB3-LP Schematic Wiring Diagram TB3Q Schematic Wiring Diagram TB3Q W/SWEETENER & Empty BAG Detect Schematic Wiring Diagram TB6 Schematic Wiring Diagram TB6Q
Related manuals
Manual 11 pages 51.02 Kb

TB6Q, TB6 specifications

The Bunn TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers are a popular series of commercial machines designed for high efficiency and optimal performance in busy environments such as cafes, restaurants, and offices. These machines are crafted with a focus on quality, dependability, and advanced brewing technology to deliver a superior coffee experience.

One of the standout features across the Bunn TB series is the ability to brew large quantities of coffee quickly. The TB6Q, for instance, can brew up to 6 gallons of coffee per hour. This high volume brewing capability ensures that establishments can keep up with demand, especially during peak hours. Additionally, the machines come with a unique design that incorporates a pre-infusion feature, allowing for the coffee grounds to be evenly saturated before brewing begins, enhancing the flavor extraction process.

The TB3-LP model is designed for low-profile applications where counter space may be limited. Despite its compact design, it still offers impressive performance, brewing up to 3.8 gallons per hour. The low-profile feature makes it an ideal choice for settings that require efficiency and space optimization without compromising on the quality of the brew.

Another notable member of the series, the TB3Q and TB3Q-LP, feature a quick brew ratio, allowing users to brew up to 3 gallons of coffee in just a few minutes. These models are equipped with easy-to-use controls for simplified operation, making them perfect for staff training and user accessibility.

All models in the TB series include a hot water faucet, allowing users to dispense hot water for tea or other hot beverages quickly. This versatility adds significant value, especially in multi-beverage settings.

Regarding durability, the Bunn TB series is constructed with high-quality materials, ensuring longevity and reliability. The machines also feature internal components that are easy to access for maintenance, thus reducing downtime and improving the overall efficiency of the machine.

In terms of technology, these brewers often incorporate advanced diagnostics to promptly identify service needs or issues. The machines come with a precise brewing temperature control system that ensures each cup is brewed at the optimal temperature for maximum flavor extraction.

Overall, Bunn's TB6Q, TB3-LP, TB6, TB3Q, and TB3Q-LP coffee brewers represent the culmination of advanced brewing technology and practical design for commercial coffee solutions. Their efficiency, quality, and ease of use make them a staple in many establishments, solidifying Bunn's reputation as a leader in the coffee brewing industry.
Top Page Image Contents