Bunn CDBCF TC, CDBCF APS, CDBC APS manual Adjustments & Optional Settings, Setting Brew Temperature

Page 8

ADJUSTMENTS & OPTIONAL SETTINGS

HIDDEN

SWITCH

P1866

Setting Brew Temperature

The brewer is factory set to brew at 200°F (95°C). To change this setting, press and hold the "HIDDEN" switch beneath the "¨". The word "TEMP" above the "ON/OFF" switch will glow to correspond with the temporary function change of this switch. Repeatedly press and release the "ON/OFF" switch until one of the bank of temperature indicators shows the approximate desired temperature. When two indicators are glowing, the temperature is approximately the number between them.

Setting Brew Lockout

The brewer is factory set with the brew lockout disabled. Brew lockout prevents starting a brew cycle if the ready indicator is not glowing. When an attempt at brewing cannot be allowed, the word "NOT" and "LOCKOUT" flash for three seconds to indicate the reason the brew can't begin. To change the condition of the brew lockout, press and hold the "HIDDEN" switch beneath the "¨" and momentarily press the "BREW" switch.

Adjusting Automatic Warmer Shut-Off

The brewer is factory set with this feature disabled. The automatic warmer shut-off de-energizes all warmers after a predetermined time period after the most recent brew cycle. To change the setting, press and hold the "BREW" switch and the "HIDDEN" switch beneath the "¨" for five seconds, the entire bank of temperature indicators will flash on-and-off. Release both switches. Pressing and releasing the "BREW" switch will select the number of temperature indicators from none to five. When no indicators are glowing, this feature is disabled and all warmers will be controlled only by their respective switches. When one to five indicators are glowing, it indicates the approximate number of hours of delay before all warmers will be automatically de-energized after the most recent brew cycle.

IMPORTANT: The tank must be full and fill solenoid shut off prior to making these adjustments. The sprayhead must be installed when making adjustments.

Adjusting Brew Volumes

The brewer is factory set to deliver 64 ounces ± 2 for each brew cycle.

BREW VOLUME SET-UP: Use the following steps when the setting is unknown or a different circuit board is being installed.

1.Place an empty funnel in the funnel rails and an empty decanter or graduated vessel beneath the funnel.

2.Press the "ON/OFF" switch (Indicator glowing).

3.Press and hold the brew start button until you hear the brew solenoid click on-and-off three times (approximately 10 seconds). Release the button.

4.Allow the cycle to continue until the desired amount of water is dispensed and then turn "OFF" the brewer. The brewer is now set to dispense this amount of water for each subsequent brew cycle.

To increase the amount of water for each brew cycle place an empty funnel in the funnel rails and an empty decanter or graduated vessel beneath the funnel. Press the "ON/OFF" switch. Press and hold the "BREW" switch

Page 8

29707.1 021804

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Disco Ntinued V ERS ION Contents IntroductionUser Notices CDBCF-DV BrewersCdbcf APS-DV Brewers Cdbcf APS-DV & TC-DV Brewers#02765.0000 #12364.0000 #00656.0000 Models CDBC-DV, CDBC-APS DV & Cdbcf TC-DV Electrical RequirementsPlumbing Requirements Initial SET-UPCoffee Brewing Faucet ModelsCleaning Operating ControlsAdjustments & Optional Settings Setting Brew TemperatureNow disabled Pulse Brew Setup ProceedureWater Sensing Threshold Adjustment Procedure Troubleshooting Before troubleshooting this brewer, check for the followingRemedy TroubleshootingRefill Circuit Problem Probable Cause Troubleshooting Refill Circuit Heating Circuit Problem Water does not heat to proper tem- peratureTroubleshooting Heating Circuit Problem Probable CauseTank Heater Ings are takenProblem Probable Cause Remedy Brewing Circuit Problem Probable Cause Troubleshooting Brewing Circuit Consistently low beverage level Brew volumeDispenser Be made with sprayhead installed Brew cycle will not start Control board or dispense valveWater temperature Set-upinstructionsDripping from sprayhead Lime build up RequiredProblem Probable Cause Diagnostics Cause Things to CheckWhen servicing, except when electrical tests are re Component AccessService Control BoardSwitch Panel Dispense Valve Limit Thermostat Wiring Limit ThermostatTank Heaters Valve from the bottom of the tank29707.1 Voltage Selector Switch Voltage Selector Switch TerminalsRefill Valve Warmer Elements Schematic Wiring Diagram Cdbc DV Schematic Wiring Diagram Cdbc APS-DV Cdbcf APS/TC/LPTC-DV

CDBC TC, CDBC APS, CDBCF TC, CDBCF APS specifications

The Bunn CDBCF series of coffee brewers is an essential tool for any coffee business, renowned for its reliability and efficiency. This series offers different models including the CDBCF APS (Automatic Pour-Over) and CDBCF TC (thermo carafe), among others. Each of these brewers is designed to produce exceptional quality coffee while ensuring ease of use.

One of the main features of the Bunn CDBCF APS is its automatic pour-over capability, which ensures that water is heated to the perfect brewing temperature and dispensed consistently. This model is equipped with a stainless steel water tank that maintains optimal water temperature, resulting in flavorful coffee extraction. Furthermore, the APS model allows for quick brewing cycles, producing up to 3.8 gallons of coffee per hour, making it ideal for high-demand environments.

The CDBCF TC model, on the other hand, utilizes a thermal carafe to keep coffee hot for extended periods without the need for a hot plate. This technology not only preserves the coffee’s flavors and aromas but also minimizes energy consumption. The thermal carafe can hold up to 1.9 liters of brewed coffee, making it efficient for serving in busy settings.

Both models in the CDBCF series come with a simple interface for straightforward programming and operation. Features such as the BrewLOGIC technology help regulate the brewing time and monitor water flow to ensure consistency. This is particularly beneficial in maintaining the quality of coffee across multiple brewing batches.

In terms of build quality, Bunn CDBCF brewers are constructed with durable materials designed to withstand the wear and tear of daily use in busy coffee shops. Their compact design requires minimal counter space while providing a high volume of output.

Overall, the Bunn CDBCF APS and TC models stand out for their advanced brewing technologies, versatility, and user-friendly design. They cater perfectly to coffee enthusiasts and business owners looking for reliable brewing solutions that deliver consistent quality and taste. With the Bunn CDBCF series, coffee brewing becomes not only an art but also an efficient and seamless process.
Top Page Image Contents