Cuisinart WCH-1500 Replacing Water Filter, Filling the Internal Tanks, Setting the Filter Timer

Page 5

Filling the Internal Tanks

Tank

NOTE: Energy Saver switch must be in the

NOTE: Upper and lower

Off position for water to heat.

 

 

 

Upper

 

tanks must be completely

 

 

 

4. After about 1 hour and 20 minutes, the BLUE

 

 

 

full before proceeding.

Lower

cold water indicator will light up, signaling

1. Place a glass under the

 

Tank

water is chilled.

 

 

right spigot and press

 

NOTE: On subsequent fill-ups, unit should take

and continue to hold

 

less than 10 minutes to heat and 30 minutes

the COLD button until

 

to chill.

water flow becomes

 

5. Press and hold each button to ensure all air

steady (may take up

 

 

has been purged from the unit so water flow

to 3 minutes).

 

 

is steady.

2. Repeat process with ROOM button, and then

Initiating Energy Saver Mode

with the HOT button until all flow steadily.

 

 

You can turn off the heater used to heat the

NOTE: When filling hot and cold internal tanks,

water in the hot tank to reduce the system's

the water level in the lower tank will drop and

 

energy usage by more than 50%. While in

you will hear the filling process taking place.

 

Energy Saver mode, you can still dispense water

Setting the Filter Timer

 

from your hot tank; however, it will not

The filter timer, located on the lid of the unit, lets

be heated.

NOTE: We recommend you power your unit off

you know when to change your water filter. Each

filter will last for 3 months.

 

when only room temperature filtered water

1. Once unit is set up and all water tanks are full,

is needed.

1. Put the Energy Saver switch in its On position.

peel off the “Filtering” sticker from the filter

 

timer screen.

 

2. The green LED will light up, indicating your

 

 

 

 

2. Press and hold the Start button until

 

unit is in Energy Saver mode.

Filtering is displayed (approx. 5 seconds).

3. Because your unit is in Energy Saver mode

 

 

 

 

3. In 12 weeks, the word REPLACE will appear.

and your hot water heater is disabled, the red

For best results, we recommend inserting a

LED hot water indicator light will turn off when

new Cuisinart® Water Filter immediately.

 

the temperature of the hot water decreases

4. You may turn off the timer and display by

 

(this can take up to 2 hours).

 

4. To resume your hot water, simply put the

pressing the Start button for 5 seconds.

 

Once you replace the filter, reset the timer by

Energy Saver switch in its Off position. After

pressing the Start button for 3 seconds.

 

about 15 minutes, the red LED hot water

NOTE: You may reset the timer at any time by

indicator will light up, signaling hot water is

ready to dispense.

pressing and holding the Start button for

 

 

NOTE: If your unit has been in Energy Saver

3 seconds.

 

OPERATING INSTRUCTIONS

mode for longer than a week, we recommend

you flush out your hot water tank by dispensing

Once set up is completed, tanks are filled and

 

and disposing of a full glass of water from the

water is flowing steadily, your unit is ready to use!

left spigot before enjoying your first glass of hot

1. Close the lid and plug unit into outlet.

 

water.

 

Replacing Water Filter

2. Press the On/Off power switch on the control

panel to turn on. The BLUE light around the

Replacement filters may be purchased at most

power switch indicates the unit is on and

 

retail outlets or www.cuisinart.com. To replace

cooling and heating functions are activated.

your filter, follow “Water Filter Setup” on page 4.

3. After about 15 minutes, the RED hot water

indicator will light up, signaling hot water is TIPS AND HINTS ready to dispense.

• Drinking 4 to 8 glasses of water each day is healthy! Your countertop chiller makes it easy.



Image 5
Contents Cuisinart Countertop Filtration System For your protection, this unit Special Cord SET InstructionsOutlet as shown in figure A. If a grounding-type outlet is Obtained so that a 2-slot wall outlet can be usedIntroduction ContentsParts and Features Installing the Prepared Water Filter Setup are completePreparing the Water Filter Filling the Upper and Lower TanksSetting the Filter Timer Initiating Energy Saver ModeReplacing Water Filter Filling the Internal TanksSymptom Possible Cause Solution Cleaning and careTroubleshooting Installed on the bottom of the base Temperature water wasSubsequent fill-ups Cold water LED Large amount of room Light turns off evenStoring the unit Technical specificationsPerformance Data Sheet for Models WCH-1000 and WCH-1500 Performance data sheetPurchases Made in Iowa Limited Three-Year Warranty WarrantyIB-8896A
Related manuals
Manual 13 pages 11.19 Kb