Step-by-step installation instructions.
Electronic Faucet Installation (not available on all models)
Be sure there is room underneath the sink to make the needed connections. Select one of the following places to install the faucet:
NOTE: Looking at fourth illustration at right, be sure the faucet base will fit flat against the surface at the selected location so the gasket will seal. The base may have to be angled sideways or diagonally.
| If drilling is needed, make a 1″ – 1 1⁄4 ″ dia. hole. Be sure to use the | |
1 | ||
proper procedure for drilling porcelain or stainless steel. Special drill | ||
| ||
| bits may be needed. | |
| Looking at first illustration, insert a screw into the | |
2 | ||
base mounting hole. Turn a flat nut a few turns onto the screw. | ||
| ||
| Position the base gasket over the mounting hole. Set the base on | |
3 | ||
the gasket, routing the leadwire through the mounting hole. | ||
| ||
| Holding the flat nut under the sink with one finger, tighten the | |
| screw until just snug. | |
| Turn the remaining flat nut a few turns onto the other screw. | |
4 |
Screw (2)
Faucet base
Nut (2)
TOP VIEW
Nut (2) Screw (2)
Faucet base |
|
|
|
|
| 1″ – 1 1/4″ dia. |
|
|
|
|
|
| mounting hole |
Gasket |
|
|
|
| in sink or | |
|
|
| countertop | |||
|
|
|
|
|
|
|
| Position the screw in the slotted base mounting hole and tighten | |
|
| ||
|
| until snug. Make sure the gasket position is properly aligned and | |
|
| carefully tighten both screws until the base is held firmly in place. | |
|
| Do not overtighten and break the base. | |
|
| Assemble the top faucet base and hex nut onto the faucet stud | |
| 5 | ||
| (third illustration). Tighten the nut until snug. | ||
| |||
|
| stud.Insert tubing insert into tubing adapter. Securely tighten to faucet | |
6 | |||
|
| ||
|
| Feed the length of 3/8″ OD tubing from the bottom up through | |
| 7 | ||
| the faucet base. Connect to the tubing adapter as shown in fourth | ||
| |||
|
| illustration, tightening the compression nut securely. | |
|
| Remove the short shipping tube and screw the spout into the | |
| 8 | ||
| faucet body. | ||
| |||
|
| Lower the faucet assembly and lock into place on the faucet base. | |
9 | |||
| |||
Battery Pack Installation and Connection |
Lever
Spout
Faucet
Faucet stud
Top faucet base
Hex nut
Tubing insert
ASSEMBLED
| In a dry location, within reach of the electronic base 3′ lead wire, | |
1 | ||
select a place for the battery pack (see illustration on page 5). | ||
| ||
| The battery pack attaches to most surfaces, using the included | |
| ||
| The battery pack uses two size AA batteries. Check to be sure they | |
2 | ||
are installed correctly. Then, remove the paper backing | ||
| ||
| on the Velcro™ strip and secure the pack in place. | |
| Fasten electronic base lead wire and battery pack connector | |
3 | ||
together. | ||
|
8
Tubing adapter
Compression nut |
Tubing insert
Tubing adapter
Compression nut
3/8″ tubing, (run to Filter 2 outlet)
Faucet base
Base lead wire connector (to battery pack)