Hoshizaki F-450MAH Removal and Replacement of Components, Service for Refrigerant Lines

Page 35

V. Removal and Replacement of Components

IMPORTANT

1.The Polyol Ester (POE) oils used in R-404A units can absorb moisture quickly. Therefore it is important to prevent moisture from entering the system when replacing or servicing parts.

2.Always install a new filter drier every time the sealed refrigeration system is opened.

3.Do not leave the system open for longer than 15 minutes when replacing or servicing parts.

1.Service for Refrigerant Lines

[a] Refrigerant Recovery

The icemaker unit is provided with two refrigerant access valves - one on the low-side and one on the high-side line. Using proper refrigerant practices recover the refrigerant from the access valves and store it in an approved container. Do not discharge the refrigerant into the atmosphere.

[b]Evacuation and Recharge [R-404A]

1)Attach charging hoses, a service manifold and a vacuum pump to the system. Be sure to connect charging hoses to both high-side and low-side access valves.

IMPORTANT

The vacuum level and vacuum pump may be the same as those for current refrigerants. However, the rubber hose and gauge manifold to be used for evacuation and refrigerant charge should be exclusively for POE oils.

2)Turn on the vacuum pump. Never allow the oil in the vacuum pump to flow backward.

3)Allow the vacuum pump to pull down to a 29.9" Hg vacuum. Evacuating period depends on pump capacity.

4)Close the low-side valve and high-side valve on the service manifold.

5)Disconnect the vacuum pump, and attach a refrigerant service cylinder to the high-side line. Remember to loosen the connection, and purge the air from the hose. See the nameplate for the required refrigerant charge. Hoshizaki recommends only virgin refrigerant or reclaimed refrigerant which meets ARI Standard No. 700-88 be used.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Modular Flaker Models 450MAH-C Hoshizaki AMERICA, INC Contents Water TEMP. F Specifications 1. F-450MAH450MAH-C II. General Information Construction Control Box Layout Solid-State Control Timer BoardTimer Board Sequence Part Code Page Page 450MAH Wiring Diagram450MAH-C Sequence of Electrical Circuit Page Compressor starts about 60 sec. after gear motor starts Page Low water except water-cooled model Page Page Page Page Page Timing Chart Gear Motor Relay OFF FAN Motor Flush ICE OFF Upper Lower Bottom ICE Production Performance Data883 891 898 IV. Service Diagnosis No Ice Production Problem Possible Cause Remedy Problem Possible Cause Remedy Low Ice Production Other Evacuation and Recharge R-404A Removal and Replacement of ComponentsService for Refrigerant Lines Refrigerant RecoveryBrazing Removal and Replacement of Compressor Removal and Replacement of Drier Removal and Replacement of Expansion Valve Auger Removal and Replacement of Evaporator AssemblyCutter Extruding HeadGear Motor Bearing-Lower and Mechanical SealRemoval and Replacement of Control Water Valve Removal and Replacement of Fan MotorRemoval and Replacement of Flush Water Valve Preparing the Icemaker for Long Storage VI. Cleaning and MaintenanceCleaning Solution Cleaning and Sanitizing InstructionsCleaning Procedure Sanitizing Procedure Initial Sanitizing SolutionSanitizing Procedure Final Page Maintenance Instructions

F-450MAH-C, F-450MAH specifications

Hoshizaki F-450MAH and F-450MAH-C are advanced ice machine models designed for commercial use, ensuring high efficiency and reliability in providing ice for a variety of foodservice and hospitality applications. These models are recognized for their streamlined operation and innovative technology, making them a preferred choice for many establishments.

One of the standout features of the Hoshizaki F-450MAH is its impressive ice production capacity. The machine can produce up to 525 pounds of crescent cube ice daily, meeting the high demands of busy restaurants, bars, hotels, and catering services. The ice produced is not only uniform in size but is also perfect for mixed drinks, chilling beverages, and food display applications.

The F-450MAH and its counterpart, the F-450MAH-C, are equipped with an advanced water-cooled condenser, optimizing performance even in challenging environments. This technology allows the machines to operate efficiently, minimizing energy consumption and enhancing overall performance. Additionally, these models feature a self-cleaning function that reduces maintenance time and improves hygiene by automatically flushing water lines and purging scale buildup.

Hoshizaki prioritizes durability and reliability in its designs, and the F-450MAH is no exception. The machine is constructed from high-quality stainless steel, ensuring resistance to corrosion and easy cleaning. Furthermore, the interior of the ice bin is designed to be easy to access, allowing quick retrieval of ice while maintaining optimal hygiene standards.

In terms of usability, the F-450MAH and F-450MAH-C come with a user-friendly digital control panel that provides real-time information on ice production and machine status. Operators can easily monitor performance and make adjustments as necessary, enhancing operational efficiency.

The Hoshizaki F-450MAH-C variant is tailored for those in need of a modular unit. It is designed to be stacked with compatible storage bins or dispensers, offering flexibility in installation and ice storage solutions. This modularity allows businesses to customize their ice-making operations according to specific needs while maximizing space.

In summary, the Hoshizaki F-450MAH and F-450MAH-C are exceptional ice machines that combine high production capacity, advanced technologies, and robust construction. These models offer an excellent solution for businesses in the foodservice industry, ensuring a consistent supply of high-quality ice while reducing operational costs and maintenance efforts. With their reliable performance and user-friendly features, they are regarded as a top choice in the commercial ice machine market.
Top Page Image Contents