Hoshizaki KML "F" SERIES, KML "H" SERIES service manual Setting Time

Page 41

2) Defrost Timer

No adjustment is required under normal use, as the Defrost Timer is adjusted to the suit- able position. However, if necessary when all the ice formed on the Evaporator does not fall into the bin in the harvest cycle, adjust the Defrost Timer to longer setting by adjusting the Dip Switch (No. 1 & 2) on the Controller Board.

SETTING

 

TIME

Dip Switch

Dip Switch

 

No. 1

 

No. 2

 

OFF

 

OFF

60 seconds

ON

 

OFF

90 seconds

OFF

 

ON

120 seconds

ON

 

ON

180 seconds

3) Drain Timer

The Drain Timer is factory-adjusted, and no adjustment is required.

SETTING

 

TIME

Dip Switch

Dip Switch

 

 

No. 3

No. 4

T1

T2

OFF

OFF

10 seconds

150 seconds

ON

OFF

10 seconds

180 seconds

OFF

ON

10 seconds

120 seconds

ON

ON

20 seconds

180 seconds

T1: Time to drain the Water Tank

T2: Time to restrain defrost completion

4) Drain Counter

CAUTION

Do not adjust the Drain Counter, or the Evaporator may freeze up.

The Drain Counter is factory-adjusted to drain the Water Tank every 10 cycles, and no adjustment is required. However, where water quality is bad and the icemaker needs a pump drain more often, the Drain Counter can be adjusted as shown in the table below:

41

Image 41
Contents KML F Series KML H Series Hoshizaki AMERICA, INC Contents Wiring Diagrams Removal and Replacement of FAN Motor KML-250MAH SpecificationsKML-250MWH KML-350MAF KML-350MWF KML-350MAH KML-350MWH Beginning serial #L00001J, ending Serial #M20060C KML-350MWH Beginning serial #M30061E KML-450MAF KML-450MWF KML-450MAH KML-450MWH Beginning Serial #L00001D, ending Serial #M10530B KML-450MWH Beginning Serial #M20531D KML-600MAF KML-600MWF KML-600MRF KML-600MAH KML-600MWH Beginning Serial #L00001D, ending Serial #M10115C KML-600MWH Beginning Serial # M10121E KML-600MRH Condenser Unit URC-7F Specifications URC-7F KML-250MAH, KML-350MAF, KML-350MAH, KML-450MAF, KML-450MAH II. General Information ConstructionKML-250MWH, KML-350MWF, KML-350MWH, KML-450MWF, KML-450MWH KML-600MAF, KML-600MAH KML-600MWF, KML-600MWH KML-600MRF, KML-600MRH SOLID-STATE Control Controller BoardController Board For machines with thermostat, there is no connection on K4Page Minute Fill Cycle Beep every 3 sec. = High Evaporator Temperature 127 FHarvest Cycle Freeze CycleControl Products HOS-001A Board Important Water Valve opening is limited to 6 minutes Sequence 1st Cycle2nd Cycle and after with pump drain 2nd Cycle and after with no pump drain For Models with Mechanical BIN Control Controls and AdjustmentsFor Models with Thermostat Page Setting Time Models with Thermostat Checking the Controller Board Models with Mechanical BIN ControlService Switch SwitchesControl Switch Mechanical BIN Control Proximity SwitchThese Instructions not Applicable to Models with Thermostat Explanation of OperationTroubleshooting Mechanical BIN Control only Water Circuit and Refrigerant Circuit III. Technical InformationPage KML-600MRF, KML-600MRH Wiring Diagrams KML-250MWH Pressure Switch KML-350MWF KML-350MAFKML-350MWH Beginning Serial #M40081G Beginning Serial #M20291G KML-350MAHKML-450MAF and KML-450MWF KML-450MWH Pressure Switch KML-450MWH Beginning Serial #M30711G Beginning Serial #M22771G KML-600MWF KML-600MAFKML 600MRFPage Page Beginning Serial #M20331E Beginning Serial #M20141F KML-600MRHControls and Adjustments Timing ChartWash Performance Data KML-250MWH KML-350MAF KML-350MWF KML-350MAH KML-350MWH Serial #L00001J through M20060C KML-350MWH Beginning Serial #M30061E KML-450MAF KML-450MWF KML-450MAH KML-450MWH Serial #L00001D through M10530B KML-450MWH Beginning Serial #M20531D KML-600MAF KML-600MWF KML-600MRF KML-600MAH KML-600MWH Serial #L00001D through Serial #M10115C KML-600MWH Beginning Serial #M10121E KML-600MRH Problem Possible Cause Remedy IV. Service Diagnosis 1. no ICE ProductionController Board Clean LOW ICE Production Evaporator is Frozen UPOthers Abnormal ICEService for Refrigerant Lines Removal and Replacement of ComponentsRefrigerant Recovery Evacuation and Recharge R-404ABrazing Removal and Replacement of Compressor Important Removal and Replacement of Drier Removal and Replacement of Expansion Valve Removal and Replacement of HOT GAS Valve and Line Valve Page Removal and Replacement of Evaporator Important Page Adjustment of Water Regulating Valve WATER-COOLED Model only Page Removal and Replacement of Thermistor Caution Removal and Replacement of FAN Motor Removal and Replacement of Water Valve Removal and Replacement of Spray Tubes Removal and Replacement of Pump MotorPreparing the Icemaker for Long Storage VI. Maintenance and Cleaning InstructionsPage Cleaning Procedure Page Sanitizing Procedure Following Cleaning Procedure Maintenance

KML "F" SERIES, KML "H" SERIES specifications

The Hoshizaki KML "H" Series and KML "F" Series are state-of-the-art commercial ice machines designed to meet the diverse needs of the foodservice industry. Renowned for their reliability, efficiency, and innovative technology, these ice machines are perfect for restaurants, bars, and hotels seeking high-quality ice production.

The KML "H" Series focuses on producing crescent cubed ice, a preferred choice for many establishments due to its slow melting rate and ability to chill beverages effectively. One of the main features of the "H" Series is the ice-making process, which utilizes advanced technology to ensure a quick production cycle. The machines come with a variety of capacities to suit different business sizes, ranging from small-scale operations to large commercial needs.

The KML "F" Series, on the other hand, is designed to produce flaky ice, which is ideal for display in seafood and salad bars. This series stands out with its unique ice texture, perfect for preserving freshness and enhancing presentation. The "F" Series also boasts high production rates, ensuring a continuous supply of ice even during peak hours.

Both series come equipped with Hoshizaki's exclusive Cascade Ice Making System, which enhances water flow and improves efficiency, leading to lower energy consumption. This is complemented by an exterior that is easy to clean and maintain, reducing labor costs associated with upkeep.

Key characteristics of the KML Series include durable stainless-steel construction, providing longevity and resistance to corrosion. Moreover, both series feature a self-diagnostic control system that alerts users to potential issues before they become significant problems, thereby minimizing downtime.

In addition to their robust design and performance, they also incorporate environmental considerations. Hoshizaki machines are engineered to operate using refrigerants that have a lower impact on the ozone layer, making them compliant with global environmental standards.

Overall, the Hoshizaki KML "H" Series and KML "F" Series stand out in the competitive landscape of commercial ice machines, combining innovative technology, exceptional durability, and user-friendly features to provide a reliable ice-making solution for various foodservice applications.