Manitowoc Ice STH003 manual Installation, Location of ICE Machine

Page 13

The location must not obstruct airflow through or around the ice machine (condenser airflow is in and out the front). Refer to the chart below for clearance requirements.

INSTALLATION

LOCATION OF ICE MACHINE

The location selected for the ice machine must meet the following criteria. If any of these criteria are not met, select another location.

•The location must be indoors.

•The location must be free of airborne and other contaminants.

•Air temperature: must be at least 50ºF (10ºC) but must not exceed 110ºF (43ºC).

•The location must not be near heat-generating equipment or in direct sunlight.

•The location must be capable of supporting the weight of the ice machine and a full bin of ice.

•The location must allow enough clearance for water, drain, and electrical connections in the rear of the ice machine.

•

Top/Sides

Back

	Self-Contained	Self-Contained
	Air-Cooled	Water-Cooled
	5" (127 mm)*	5" (127 mm)*
	5" (127 mm)*	5" (127 mm)*
	5" (127 mm)*	5" (127 mm)*

*NOTE: The ice machine may be built into a cabinet.

There is no minimum clearance requirement for the top or left and right sides of the ice machine. The listed values are recommended for efficient operation and servicing only.

CAUTION

The ice machine must be protected if it will be subjected to temperatures below 32 F (0 C). Failure caused by exposure to freezing temperatures is not covered by the warranty.

13

Image 13

Contents CM050 CM Model Ice Machines Safety Notices Procedural Notices Personal Injury Potential Read These Before ProceedingPotential Personal Injury Situation Table of Contents Liquid Line Thermistor Model Numbers CMS050A004Manitowoc ICE Machine Cleaner and Sanitizer Accessories LegsDrain Pump MODEL/SERIAL Number Location General Owner Warranty Registration CardPage Manitowoc ICE, INC Location of ICE Machine InstallationHeat of Rejection Air Conditioning** Peak ICE Machine Heat of RejectionLevelers Legs Leveling the ICE MachineWater Inlet Lines Water SERVICE/DRAINS Water SupplyDrain Connections Water Supply and Drain Line SIZING/CONNECTIONS Drain PumpElectrical Requirements Voltage Electrical SpecificationsMinimum Circuit Ampacity Gfci RequirementsComponent Identification Water Pump Evaporator Shutter Assembly Power Button Green BIN Thermostat AdjustmentClean Green Operational ChecksSafety Timers ICE Machine Inspection Cleaning the CondenserAIR-COOLED Condenser Interior Cleaning and Sanitizing Place CLEANING/SANITIZING Procedure Interior Cleaning and Sanitizing GeneralPage Cleaning Procedure Page Page Removal of Parts for Cleaning and Sanitizing TOP Cover Water Shutters ICE Chute Sump Drain Overflow Tube Water Trough Spray BAR, Water Pump and Hose Spray BAR Disassembly SELF-CONTAINED AIR-COOLED ICE Machines Removal from SERVICE/LONG Term STORAGE/WINTERIZATION GeneralFreeze Refrigeration System Start-UpHarvest Automatic Shut-OffSequence Energized Parts Chart SELF-CONTAINED ICE MachinesDiagnosing AN ICE Machine That will not RUN TroubleshootingPage ICE Machine will not Harvest ICE Quality is Poor Cubes are SHALLOW, Incomplete or White Freeze Cycle is LONG, LOW ICE Production ICE Machine Runs & no ICE is Produced Freeze Harvest Cycle Psig Beginning Freeze Cycle Discharge Pressure LOW Checklist Analyzing Suction Pressure Step ProcedureSuction Pressure LOW Checklist Problem Suction Pressure High Checklist ProblemDischarge Pressure General HOT GAS ValveNormal Operation HOT GAS Valve Analysis Freeze cycle. If Function SpecificationsNo Ice on Ice on Bulb Result Check ProcedureFreeze Time Harvest Time Total Cycle Time Additional finishing time check Adjusting Finishing TimeLiquid Line Thermistor SM50 Resistance Chart TEMPERATURE/RESISTANCE ChartTotal System Refrigeration Charge Component Specifications Check Procedures Single Phase Compressors Compressor Electrical DiagnosticsCheck Resistance OHM Values Check Motor Windings to GroundCompressor Drawing High Amps Compressor Drawing Locked RotorRelay CapacitorPage Cycle Times Freeze Time + Harvest Time = Cycle Time New Product Specifications RecoverRecycle ReclaimRefrigerant RE-USE Policy Page Connections Refrigerant Recovery/Evacuation/ChargingRecovery/Evacuation Charging Procedures Page System Contamination Cleanup General No symptoms or suspicion Normal Mild System Contamination Cleanup Procedure Change the vacuum pump oil Severe System Contamination Cleanup ProcedureFollow normal evacuation procedures Page FIG. a Pinching OFF Tubing Using Pinch Off ToolDo not disassemble valve Brazing Procedures for Danfoss Solenoid ValvesMAX F 700C Liquid Line Filter Drier Control Board Wiring Diagrams Tubing Schematic Manitowoc Ice, Inc