Ice-O-Matic IOD200, IOD150 installation manual Installation, Drip Tray Assembly

Page 5

Installation

IOD150, IOD200, IOD250

1.Locate the ice dispenser on the counter. Allow vertical clearance above the unit for the removal of the cover and for pouring ice into the hopper.

2.Plan the unit drain. A one-inch (1”) I.D. drain tube is required for draining. Routing is either through the back or the base. Sufficient fittings are included with the unit to install in most cases.

3.In order to comply with the National Sanitation Foundation (NSF) requirements, this unit must be either elevated above the counter top sufficiently to provide space for cleaning under the unit or sealed to the countertop

Elevating the unit may be accomplished by using the legs. They will screw into threaded holes in the base of the unit. Note: Before installing legs the plastic plugs must be removed.

IMPORTANT:

It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A112.1.2-1979: or an approved vacuum breaker or other such method as proved effective by test.

Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed and maintained according to Federal, State and Local Codes.

DRIP TRAY ASSEMBLY

Drip Tray Drain Assembly (See Illustration Below): Route the drain tube to an open drain with the end of the tube above the “flood” level of the drain. Use the tubing, fittings, clamps and insulation provided with the Dispenser to assemble the drain. The completed drain line must pitch continuously downward and contain no “traps” or improper drainage will result.

Drip Tray Drain Fitting

Solvent Bond

Note: This equipment must be installed with adequate backflow protection to comply with Federal, State and Local Codes.

Hose Clamp

Coupling ¾ Socket x ¾ FPT

Barb Adapter 1” Barb x ¾ MPT

Drain Line 1-Inch Plastic Tubing with Insulation

Page 4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Page Introduction Table of ContentsOptions Field Installed Specifications and LimitationsDispenser Specifications Dimensions InchesSite Preparation For The InstallerEquipment Description Drip Tray Assembly InstallationWater Glass Filler Kit Water Glass Filler Kit Con’t IOD150 DimensionsIOD200 and IOD250 Dimensions Completion Initial Start UpGate Restrictor Plate AdjustmentCleaning Precautions Cleaning and SanitizingSanitize the Ice Storage System Monthly and Initial Start UPTroubleprobable Cause TroubleshootingWiring Diagram

IOD200, IOD150 specifications

Ice-O-Matic has long been recognized as a leading manufacturer of ice machines, and the IOD150 and IOD200 models exemplify the company's commitment to quality, efficiency, and innovation in ice production. Designed to cater to a variety of commercial needs, these machines are engineered to be reliable and effective, making them an excellent choice for restaurants, bars, hotels, and convenience stores.

One of the standout features of both the IOD150 and IOD200 is their advanced ice production capabilities. The IOD150 can produce up to 152 pounds of ice per day, while the IOD200 increases that capacity to an impressive 202 pounds. This high-output performance ensures that businesses can meet their ice needs even during peak hours, providing customers with consistently chilled beverages and food items.

Both models are equipped with a built-in storage bin that offers ample space for ice storage. The IOD150 features a 70-pound storage capacity, while the IOD200's bin can hold up to 90 pounds of ice. This built-in storage design eliminates the need for separate ice bins, saving valuable floor space in busy commercial environments.

The design of the IOD150 and IOD200 models incorporates a user-friendly interface, making operation straightforward and efficient. The intelligent control systems monitor ice production and detect any maintenance needs, ensuring optimal performance and extending the lifespan of the machines. This feature is particularly beneficial for busy staff members who may not have specialized training in equipment management.

Energy efficiency is a critical consideration for businesses today, and Ice-O-Matic’s models do not disappoint. Both the IOD150 and IOD200 are designed to operate with low energy consumption, making them cost-effective choices for any enterprise. Their environmentally friendly operation aligns with the growing demand for sustainable practices in the food service industry.

In addition to performance and efficiency, hygiene and cleanliness are paramount in ice production. Ice-O-Matic has integrated a sanitation design in both models, which includes anti-microbial materials. This helps maintain the highest standards of cleanliness, minimizing the risk of contamination.

The IOD150 and IOD200 models represent Ice-O-Matic’s dedication to providing high-quality ice solutions that meet the diverse demands of commercial operations. With their robust features, advanced technology, and focus on efficiency, these machines stand out as top choices for any business seeking reliable ice generation.
Top Page Image Contents