Russound CAV6.6 Six-Zone instruction manual Zone Setup cont’d, Enable, Volume

Page 57

This defines the Controller ID for this system. The default is 1 but when multiple controllers are used, each additional controller ID must be sequential and unique and be set before being connect- ed to the system. Note that the system must be restarted before the controller will assume the new ID.

WARNING: This procedure returns the controller to its original settings - use with discretion.

Factory Initialization allows the installer to erase all programmed settings and returns the settings to the factory default settings. All settings including source equipment IR commands will need to be reentered. An “Are you sure?” prompt and a “no” response allows the installer to cancel the reset; a “yes” at the prompt will load factory/default settings.

		INSTALLER
		INSTALLATION MENU
		Zone Setup (cont’d)
5.	PAGE ENABLE -	This feature is either disabled or enabled. It allows the option of
	(PagEn)	receiving or blocking a page in a zone. If disabled, the page will
		not be sent to the zone. If enabled (default), the page will be
		sent to the zone.
6.	PAGE VOLUME -	This feature allows the installer to adjust the Page Volume for the
	(PagVl)	zone, from 0 (min) to 100 (max).

CTRLR SETUP (CtlId)

Controller Setup is the basic configuration of the controller. This setup menu selects the options for Controller ID and Factory Initialization. See Installation Menu on Page 50 and Controller Setup -

Flow Chart on page 68

1. CONTROLLER ID - (CtlId)

2. FACTORY INIT - (FInit)

POWER MGT (PwMgt)

The CAV6.6 is capable of managing the power state of the connected source equipment. The power management is configured on a source-by-source basis.

All sources that have power management enabled are initialized by a “POWER ON” command or macro which must cause the source to produce an audio signal. Power management is initialized when the first keypad is turned on or when the home theater trigger input has 12VDC present. The 12VDC trigger output is turned on when the first zone is turned on.

All sources that have power management enabled are turned off by the “POWER OFF” command after all zones have been turned off, with a timeout of five minutes.The 12VDC trigger output is turned off

57

Image 57

Contents CAV6.6 Important Safeguards Table of Contents Reference Section Favorites Party ModeDo Not Disturb Front Aux A/VCAV6.6 Controller-Front Panel Component GuideFront A/V AUX Connections UNO-S2 Keypad Command KeysUNO-TS2 Touchscreen UNO-S1 Keypad 102.5SRC2 Remote Control UNO-S2 Keypad Button Functions OperationFeature and Setting 1. Bass UNO-S2 User Menu Setting PreferencesTreble BalanceScrolls through the six audio source inputs UNO-S1 Keypad Button FunctionsParty Party Mode Master or Off UNO-S1 User Menu Setting PreferencesFeature and Setting FrtAV Front A/V Aux In Enabled/DisabledSource Control Screens UNO-TS2 Touchscreen Button FunctionsUNO-TS2 Setting Preferences User Menu SettingsGetting Started Tools needed for installationUnpacking the Components Connection TipsComponent Guide CAV6.6 Controller-Rear Panel Installer OS Update Port UNO Keypad-OS Update PortUNO-S2 Keypad UNO-S1 KeypadUNO Keypads-Rear Panel UNO-S2 UNO-S1UNO-TS2 Keypad Wiring Wiring InstructionsCAT-5 Wire Color Speaker WiringJumper Setting UNO-S2 KEYPAD-INSTALLATIONUNO-S2 Keypad Connections CAT-5 ConnectionIR Receiver Connection Keypad Location Keypad InstallationUNO System Keypad Port Connection See Sample System Configuration 3,Source IR Connections Source Audio/Video Input ConnectionsSource Audio/Video Loop Output Connections Speaker Connections ACC IR Connection Zone Audio to Amp and Video Outputs BUS Ready Sub-zone Connection 12VDC Trigger In/Out 12VDC Home Theater Trigger12VDC 50mA Trigger Out 12VDC Page Trigger 12VDC Page Trigger OutAudio/Video Installer Zone 12VDC Trigger Outputs Rnet Link In and Link Out Multiple Controllers SMS3 Rnet Link In and Link Out RNET-enabled ComponentsRS-232 Interface Programming Center Keypad Port Connection Initial Install Test System Programming Overview ProgrammingSystem Programming Overview cont’d Source Information Form Zone Information Form Macro Editor Form UNO-S1 UNO-S2 Installation Menu OverviewButton Function UNO-S1 Keypad Five-character DisplayCommand Type Installation MenuSource NUM Source NameBasic Setup cont’d To build macros, see Macro Editor Key Config cont’dTrim Level Numeric TextPrefix CMD Numeric IR cont’d Selected DefaultSelected Macro To build macros, see Macro Editor KEY FunctionMacro SRC SEL CMD SrcSCSyson Enable Source Select Command cont’dParty Enable Master EnableEnable Zone Setup cont’dVolume Controller ID CtlId Factory Init FInitPower Management cont’d Sense DelayPower on CMD OnCmd Learn IR LrnIR Power OFF CMD OfCmdLearned SRC Learn IR cont’dLEARN/DELETE Test IR?#CONTROLLERS Macro Editor cont’dBuild Time Build DateSource Setup Basic Setup Setup Menu Flow ChartsSource Setup Key Configuration Source Setup Source Names/Volume Trim Source Setup Numeric IR Source Setup Source Select Command/# of Sources Zone Setup Controller Setup Power Management Learn IR Macro Editor System Info UNO Keypad Diagnostics Menu Device Codes for Cable Device Codes for TVsDevice Codes for Video Acc Device Codes for Cable cont’dDevice Codes for SAT/DSS Device Codes for VCRsDevice Codes for Laser Disc Players Device Codes for VCRs cont’dDevice Codes for DVD Players Device Codes for Tuner/AmpDevice Codes for Amp and Misc. Audio Device Codes for CD PlayersDevice Codes for Home Control UNO-S1 UNO-S2 Source NamesTivo Six Zones and Six Sources Sample System Configuration Rnet Link In and Link Out Integrate Multiple CAV6.6’sSample System Configuration Zone Keypad Expansion Sample System Configuration BUS Ready Sub-Zone Addition Multi-Source Mode SwitchBUS Hub CAT-5 ConnectionsZONE, 1-SOURCE Zone Audio To Amp & Video Outputs Additional AmplificationSample System Configuration Home Theater Source Loop OutputsFront Left and Right Speakers Sample System Configuration KEY Function UNO-S1 TV Hdtv KEY Codes TV HdtvSAP SAP, CC KEY Function UNO-S1 Cable KEY Codes CableSAP KEY Function UNO-S1 Video ACC KEY Codes Video ACCLanguage, MTS KEY Function UNO-S1 SAT/DSS KEY Codes SAT/DSSAlt/Audio,Lang.,CC KEY Function UNO-S1 VCR KEY Codes VCRMenu Back Clear Fav Channel FavCh KEY Function UNO-S1 Laser Disc KEY Codes Laser DiscSubtitle, CC KEY Function UNO-S1 DVD KEY Codes DVD105 KEY Function UNO-S1 Receiver KEY Codes ReceiverDVD, LD KEY Function UNO-S1 AMP/MISC Audio KEY Codes AMP/MISC AudioTAPE, MD KEY Function UNO-S1 KEY Codes CDInput Tape, MD KEY Function UNO-S1 Home Control KEY Codes Home ControlInput Source/Scene CAV6.6 Controller/Amplifier Technical SpecificationWarranty & Repair Rev 05/10/06