Russound CAV6.6 Six-Zone instruction manual System Programming Overview

Page 44

INSTALLER

PROGRAMMING

System Programming Overview

This manual includes items that are designed to assist in the programming process.

Sample Configurations (Pages 80-91)

A series of sample configurations are provided to showcase a variety of system designs and compo- nent options.

Forms (pages 46-48)

Three blank reproducible forms are included as planning tools when determining sources, settings and zone preferences. The Source and Zone Information forms and the Macro Editor form should be completed before programming and referred to during the installation menu process. This speeds up programming time and reduces missed or incorrect entries. These forms also serve as system refer- ence documents if future troubleshooting is needed.

IR Device Codes (Pages 74-77)

This list of command type IR device codes reflects the built-in IR codes in the CAV6.6 library. During programming, these codes will be entered for each source at the “Device Code” prompt. If a code is not listed for a source, the Learn IR procedure is available to learn in and centrally store IR codes.

Key Functions (Pages 92-113)

This list of key functions identifies what IR codes are supported for each command type (source) by the built-in library. “Learned Only” indicates that this function is not supported and must be learned into the CAV6.6. This list of key functions reflects the different available key functions associated with what you see on the LCD panel when performing the Key Configuration procedure in the Installation Menu. The list of functions corresponds with the command types above (e.g., Tuner, CD player, etc.).

Source Names (Pages 78-79)

A list of assignable Source Names is provided for advance selection and source form completion before programming.

Flow Charts (Pages 62-72)

Installation Menu flow charts provide a graphical representation of the programming process.

Installation Menu (Pages 49-61)

The Installation Menu provides the step-by-step complete programming procedure for the keypad and the controller.

Although you can begin programming at any point within the Installation Menu, the following sequence is recommended for initial installations, as it progresses from the most basic requirements to the more advanced features.

1. Controller Setup (CTRLR SETUP) (Page 57)

This procedure sets the controller ID number within the system. This number must be manually set when multiple CAV6.6’s are linked through RNET within one system. This procedure is not necessary for systems with only one CAV6.6.

(continued)

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents CAV6.6 Important Safeguards Table of Contents Reference Section Party Mode FavoritesDo Not Disturb Front Aux A/VComponent Guide CAV6.6 Controller-Front PanelFront A/V AUX Connections Command Keys UNO-S2 KeypadUNO-TS2 Touchscreen 102.5 UNO-S1 KeypadSRC2 Remote Control Operation UNO-S2 Keypad Button FunctionsUNO-S2 User Menu Setting Preferences Feature and Setting 1. BassTreble BalanceUNO-S1 Keypad Button Functions Scrolls through the six audio source inputsUNO-S1 User Menu Setting Preferences Party Party Mode Master or OffFeature and Setting FrtAV Front A/V Aux In Enabled/DisabledUNO-TS2 Touchscreen Button Functions Source Control ScreensUser Menu Settings UNO-TS2 Setting PreferencesTools needed for installation Getting StartedUnpacking the Components Connection TipsComponent Guide CAV6.6 Controller-Rear Panel Installer UNO Keypad-OS Update Port OS Update PortUNO-S2 Keypad UNO-S1 KeypadUNO-TS2 UNO Keypads-Rear PanelUNO-S2 UNO-S1 Wiring Instructions Keypad WiringCAT-5 Wire Color Speaker WiringUNO-S2 KEYPAD-INSTALLATION Jumper SettingUNO-S2 Keypad Connections CAT-5 ConnectionIR Receiver Connection Keypad Installation Keypad LocationSee Sample System Configuration 3, UNO System Keypad Port ConnectionSource Audio/Video Input Connections Source IR ConnectionsSource Audio/Video Loop Output Connections Speaker Connections ACC IR Connection Zone Audio to Amp and Video Outputs BUS Ready Sub-zone Connection 12VDC 50mA Trigger Out 12VDC Trigger In/Out12VDC Home Theater Trigger Audio/Video 12VDC Page Trigger12VDC Page Trigger Out Installer Zone 12VDC Trigger Outputs Rnet Link In and Link Out Multiple Controllers Rnet Link In and Link Out RNET-enabled Components SMS3 RS-232 Interface Programming Center Keypad Port Connection Initial Install Test Programming System Programming OverviewSystem Programming Overview cont’d Source Information Form Zone Information Form Macro Editor Form Installation Menu Overview UNO-S1 UNO-S2Button Function UNO-S1 Keypad Five-character DisplayInstallation Menu Command TypeSource NUM Source NameBasic Setup cont’d Key Config cont’d To build macros, see Macro EditorPrefix CMD Trim LevelNumeric Text Selected Default Numeric IR cont’dSelected Macro To build macros, see Macro Editor KEY FunctionSRC SEL CMD SrcSC MacroSource Select Command cont’d Syson EnableParty Enable Master EnableZone Setup cont’d EnableVolume Controller ID CtlId Factory Init FInitPower on CMD OnCmd Power Management cont’dSense Delay Power OFF CMD OfCmd Learn IR LrnIRLearn IR cont’d Learned SRCLEARN/DELETE Test IR?Macro Editor cont’d #CONTROLLERSBuild Time Build DateSetup Menu Flow Charts Source Setup Basic SetupSource Setup Key Configuration Source Setup Source Names/Volume Trim Source Setup Numeric IR Source Setup Source Select Command/# of Sources Zone Setup Controller Setup Power Management Learn IR Macro Editor System Info UNO Keypad Diagnostics Menu Device Codes for TVs Device Codes for CableDevice Codes for Cable cont’d Device Codes for Video AccDevice Codes for SAT/DSS Device Codes for VCRsDevice Codes for VCRs cont’d Device Codes for Laser Disc PlayersDevice Codes for DVD Players Device Codes for Tuner/AmpDevice Codes for Home Control Device Codes for Amp and Misc. AudioDevice Codes for CD Players Source Names UNO-S1 UNO-S2Tivo Six Zones and Six Sources Sample System Configuration Integrate Multiple CAV6.6’s Rnet Link In and Link OutSample System Configuration Zone Keypad Expansion Sample System Configuration Multi-Source Mode Switch BUS Ready Sub-Zone AdditionBUS Hub CAT-5 ConnectionsZONE, 1-SOURCE Additional Amplification Zone Audio To Amp & Video OutputsSample System Configuration Front Left and Right Speakers Home TheaterSource Loop Outputs Sample System Configuration KEY Codes TV Hdtv KEY Function UNO-S1 TV HdtvSAP SAP, CC KEY Codes Cable KEY Function UNO-S1 CableSAP KEY Codes Video ACC KEY Function UNO-S1 Video ACCLanguage, MTS KEY Codes SAT/DSS KEY Function UNO-S1 SAT/DSSAlt/Audio,Lang.,CC KEY Codes VCR KEY Function UNO-S1 VCRMenu Back Clear Fav Channel FavCh KEY Codes Laser Disc KEY Function UNO-S1 Laser DiscSubtitle, CC KEY Codes DVD KEY Function UNO-S1 DVD105 KEY Codes Receiver KEY Function UNO-S1 ReceiverDVD, LD KEY Codes AMP/MISC Audio KEY Function UNO-S1 AMP/MISC AudioTAPE, MD KEY Codes CD KEY Function UNO-S1Input Tape, MD KEY Codes Home Control KEY Function UNO-S1 Home ControlInput Source/Scene Technical Specification CAV6.6 Controller/AmplifierWarranty & Repair Rev 05/10/06
Top Page Image Contents