Vulcan-Hart 7099A1 ML-104498 GAS Connections, Testing the GAS Supply System, Flue Connections

Page 10

GAS CONNECTIONS

All gas supply connections and any pipe joint compound used must be resistant to the action of propane gases.

The oven is equipped for a 3/4" gas pipe connection. Pipe gas supply to the oven. Make sure the pipes are clean and free of obstructions, dirt and piping compound. When connecting the gas supply to the oven, it is important that adequate size piping be run to the point of connection at the oven with as few elbows or tees as possible. Refer to piping charts or consult local gas company for piping size.

Codes require that a gas shutoff valve be installed in the gas line ahead of the oven.

All ovens are shipped with a factory preset pressure regulator. Natural gas pressure regulators are preset for 3.7" W.C. (Water Column). Propane gas pressure regulators are preset for 10" W.C. (Water Column). No further Water Column adjustment should be required. The pressure regulator is installed in the horizontal position. If the pressure regulator is to be installed in any other position, a field adjustment of the pressure regulator will be required.

WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS. USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When test pressures exceed 1/2 psig (3.45 kPa), the oven and its individual shutoff valve must be disconnected from the gas supply piping system.

When test pressures are 1/2 psig (3.45 kPa) or less, the oven must be isolated from the gas supply system by closing its individual manual shutoff valve.

FLUE CONNECTIONS

From the termination of the oven flue vent to the filters of the hood venting system, a minimum clearance of 18" must be maintained.

Do not obstruct the flow of flue gases from the flue duct located on the rear of the oven. It is recommended that the flue gases be ventilated to the outside of the building through a ventilation system installed by qualified personnel.

Information on the construction and installation of ventilating hoods may be obtained from the standard for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest edition).

This oven is equipped with a flue deflector. An optional down draft diverter may be ordered. When the diverter is supplied, it may be connected to a Type "B" vent.

LEVELING

Be sure that oven is level. Place a carpenter's level or pan of water on the oven deck. Level oven front- to-back and side-to-side by turning the adjustable feet. If the oven is not installed on legs, the floor must be level at the installation position.

— 10 —

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation Model 7019A1Important for Your Safety For Your SafetyTable of Contents Model 7000 Series Bake Oven Configurations 7018A1 7088A1 7888A1 7086A1 7016A1 7066A17019A1 7099A1 Model 7000 Series Roast Oven Configurations7096A1 7098A1 7988A1 Installation, Operation and Care Unpacking InstallationInstallation Codes and Standards LocationCasters AssemblyLegs Stacking Model 7016A1, 7018A1 and 7019A1 OvensOptional Steam Injector Nozzles Flue Connections Testing the GAS Supply SystemGAS Connections LevelingMinimum Bypass Burner Flame Adjustment Fig Electrical ConnectionsControls Fig OperationBefore First USE Shutdown Lighting and Shutting Down PilotExtended Shutdown Cooking Hints PreheatingLoading Oven PAN CapacitiesOven Inspection Window Optional CleaningStainless Steel Optional Service and Parts Information MaintenanceService Replacing Optional Lamps

7018A1 ML-104491, 7016A1 ML-104495, 7099A1 ML-104498, 7098A1 ML-104501, 7066A1 ML-104496 specifications

The Vulcan-Hart 7888A1 (ML-104493), 7019A1 (ML-104497), 7088A1 (ML-104492), 7988A1 (ML-104502), and 7086A1 (ML-104494) are advanced commercial cooking equipment designed to optimize food production in high-demand settings like restaurants and catering services. These models are part of Vulcan-Hart's trusted lineup and are known for their durability, efficiency, and cutting-edge technologies.

One of the standout features of the Vulcan-Hart models is their robust construction, which often includes stainless steel exteriors. This ensures not only longevity but also easy maintenance and cleaning, crucial in busy kitchen environments where hygiene is paramount. The emphasis on durability helps reduce the total cost of ownership as these units are less likely to suffer wear and tear.

These models are equipped with powerful heating elements that allow for quick temperature recovery and precision cooking. The Vulcan-Hart technology enables even heat distribution, which is critical for cooking a wide variety of foods evenly and efficiently. Many of these models incorporate advanced controls for temperature management, allowing chefs to maintain consistent cooking results with minimal effort.

Each of these models is designed with user-friendliness in mind. Intuitive control panels provide visual feedback and easy adjustments, reducing the learning curve for new staff. Additionally, safety features such as automatic shut-off systems protect both users and equipment from overheating and potential accidents.

Another notable characteristic of the Vulcan-Hart 7888A1 series is their multifunctionality. These units often serve as griddles, ovens, or fryers, catering to a full range of cooking methods. This versatility not only maximizes kitchen space but also allows for menu diversification, enabling establishments to offer a wide array of culinary options.

Energy efficiency is also a key consideration in the design of these models. By utilizing advanced insulation and efficient heating technology, Vulcan-Hart equipment significantly reduces energy consumption, which can lead to considerable savings on utility bills over time.

In summary, the Vulcan-Hart 7888A1 ML-104493, 7019A1 ML-104497, 7088A1 ML-104492, 7988A1 ML-104502, and 7086A1 ML-104494 exemplify the brand’s commitment to combining innovation with functionality. Their main features include durable stainless steel construction, powerful heating technology, intuitive controls, and versatility in cooking methods. These characteristics make Vulcan-Hart a preferred choice for commercial kitchens looking to optimize performance and ensure consistent food quality.
Top Page Image Contents