Sears 36511, 36519 Preparing the Counter, Control Panel END Caps, Side Trim Extension KIT

Page 5

PREPARING THE COUNTER

If you have an existing 30" wide cutout that goes all the way to the wall you may want to buy a Main Top Filler Kit No, 80279 or a 4" Backguard Kit No. 80509. These will fill in the space between the back of the range and the wall. The kits are available from Sears general catalog and may be or- dered at any Sears catalog outlet or the catalog desk at any Sears Retail Store. If this existing cutout is in a counter that has a backsplash (postformed top) we recommend that you use the 4'*Backguard.

From the illustrations below determine the dimensions of your cutout. Mark the cutout on the counter. Dimensions given are from front of counter, not from cabinet face. To minimize chipping, you may want to apply masking tape to the counter and mark the cut on top of the tape. Use a hand or saber saw to make the cut. For best appearance it is important that the cut be smooth and straight.

If you are not using the Filler or Backguard

23 3/16"

Fig. 3

Ifyou wish to set the range further back into the counter, you may notch the front of the counter up to a maximum depth of

1/2", as shown in Fig. 6. See your filler kit instructionsheet for more information.

you are using the Beckguard

---I

241/2"

Fig. 5

,1

 

 

3/8"----> _ _

30"

• 1----3/8"

/

 

 

1/2"

 

 

When the Backguard is used, the front of the counter may require notching as shown in Figures 5 and 6. See back- guard kit instruction before cuffing counter.

1/2"

Fig. 6

If you have a standard 25" countertop and you wish to set the range further back into the counter, you may notch the front of the counter up to a maximum depth of 1/2'"as shown in Figure 6. Cutout should then be 23 3/16" deep from back of notch.

If you have a countertop deeper than 25", such as in an island installation with a countertop of at least 26" and you wish to set the range further back into the counter, you may notch the front of the counter up to 1" deep, but never deeper than to the front of the cabinet face and maintaining at least 24 1/2" from the back of the notch to the inside of the rear wall of the counter. See Fig. 5.

If you are using the Filler

.[

25"l

Fig. 4

30"

_'

NOTE: If the distance from the back wall to the front of the counter backsplash (Dimension A in Fig. 7) is greater than 1 1/8", there will be a small gap between the wall behind the range and the backguard. This is normal and should not be visually objectionable.

Fig. 7

See the leveling information on previous page.

CONTROL PANEL END CAPS

If the frontof the counter is rounded, leave the curved portion on the control panel end caps. For a square counter or a notch, cut this portion off at the groove with pliers or chisel, then file smooth if necessary.

TRIM f

SQUARE COUNTER

OR NOTCH

SIDE TRIM EXTENSION KIT

If there is a small gap between the sides of the range and the cabinets (up to 1/4" each side), you can order a side trim extension kit through Sears general catalog. Order Kit No. 80769 at any Sears catalog outlet or the catalog desk at any

Sears Retail Store.

EINS19-4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Sears Contents Burner Adjustments For Your SafetyLocation Tool ListPreparing the Counter If you are using the FillerControl Panel END Caps Side Trim Extension KITLevel PreparationElectrical Connections GAS ConnectionsFlexible Connector HOOK-UP Never reuse an old connector when installing a new rangeTo Check for Leaks Rigid Pipe HOOK-UP from Floor or WallCAP Spring NAT Retainer Adjust Pressure RegulatorAdjust Burner Orifices Adjust Air Shutters Making Burner AdjustmentsTo adjust air shutters AIR Shutter SHUT-OFFVALVE Open PositionFig. A9 Step Adjust Orifice HoodsGAS Range Stability Device Installation InstructionsExcess slack in the chain could allow the range to Important Instructions for Your Safety Keep this book for later use Important Safety NoticeAlways use care when opening oven door. Let hot air Your Range Turn to set Function ButtonsBurner Ignition CooktopOven Vent 12,000 BTU BurnerTo Bake or Roast To USE the TimerAutomatic Oven OFF Recalling FunctionsCake layers Oven CookingRack Position Total Time Food = Highest Minutes = Lowest LO Broil10-12 Well DoneNeed to be repeated Before a Clean CycleAfter a Clean Cycle To SET SELF-CLEAN Cycle Self-cleaning oven finish Part Cleaning Materials RemarksBrushed chrome cooktop Glass oven door/windowGlass Collar Bulbcover PartGlass To replace burners LIFT-UP CooktopTo remove burners Removable Oven Racks Removable Oven DoorRemovable Oven Bottom To removePossible Cause ProblemDontcall for Service Until YOU Check To Adjust Oven Temperature Adjusting Oven TemperatureHOW to Order Repair Parts 801 601 63805 Number Parts List for Main TOP Section234 256 258 259 861 221 220 233 601 936 235 215 231807 293 226560 570 580 Illustration and Parts List for Wire Harnesses and Options166 173 946 183314 302 986 838 366 307 352801 374303 819 320Parts List for Broiler and Oven Burner Section KEY Kenmore 30 SELF-CLEANING GAS RANGE-MODEL Number911.3651190 Optional Rear Main Topfiller143 131 124812 @ g2 Lain ENAMELs Painted or Bright Metal Full 90..DAY Warranty on Mechanical AdjustmentsFinished Parts Sold by SEARS, Roebuck and CO., Chicago, IL

36511, 36519 specifications

Sears 36519 and 36511 are notable appliances in the home and kitchen sector, highly regarded for their combination of efficiency, functionality, and stylish design. Both models cater to a distinct market segment, with a focus on enhancing the convenience of daily tasks while also providing energy efficiency and innovative technology.

The Sears 36519 model is primarily recognized for its cutting-edge features that streamline cooking and food preparation. With a large capacity and versatile cooking options, it allows users to explore various culinary techniques such as baking, roasting, and broiling with ease. One of the main highlights of the 36519 is its intuitive control panel, which offers easy navigation through different cooking modes and settings. This appliance also comes equipped with smart technology that can connect to home Wi-Fi networks, enabling users to access recipes, cooking tips, and even receive notifications on their smartphones.

On the other hand, the Sears 36511 model emphasizes energy efficiency and sustainability, making it an excellent choice for eco-conscious consumers. This appliance has received high energy ratings, showcasing its capability to consume less electricity without compromising performance. It features advanced insulation technology, which not only retains heat effectively but also minimizes environmental impact. Additionally, the 36511 includes a self-cleaning function, allowing for hassle-free maintenance and a focus on longevity and durability.

Both models also feature sleek and modern designs that fit seamlessly into various kitchen aesthetics. Their stainless steel finishes add a touch of elegance, and the ergonomic design ensures convenience during operation. The user-friendly interfaces further enhance the overall experience, allowing individuals of all culinary skill levels to maximize their kitchen productivity.

In terms of safety, both the 36519 and 36511 incorporate several key measures, including automatic shut-off functions and child lock features that provide peace of mind in busy family households. The combination of these characteristics makes both the Sears 36519 and 36511 exemplary choices for consumers seeking reliable and efficient appliances that deliver excellent performance while prioritizing sustainability and user-friendliness. Overall, these models reflect Sears' commitment to innovation and quality in household appliances.
Top Page Image Contents