Installation Instructions
11MARK HOLES
Select the vent option that your installation will require and proceed to that section:
A. Outside top exhaust
(Vertical duct–31⁄4″ x 10″ Rectangular)
•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.
Hood mounting screws (4)
|
|
|
|
|
133⁄4″ (30″ hood) |
|
|
|
|
|
|
| 133⁄4″ (30″ hood) | |
163⁄4″ (36″ hood) |
|
|
| 163⁄4″ (36″ hood) |
|
| |||
Cabinet front |
|
|
|
|
|
|
|
|
|
| 73⁄4″ |
|
|
| Cabinet Bottom |
|
| |
| 51⁄4″ | 51⁄4″ | 11⁄4″ | 95⁄8″ |
33⁄4″ | Vertical duct |
| ||
access hole |
|
| ||
| 1⁄2″ |
|
| 13⁄8″ |
|
|
|
|
| Electrical access hole | |
Wood shims |
|
|
| (in cabinet bottom) | ||
| ||||||
line |
| |||||
minimum of 3/8″ thick |
|
|
|
| ||
and cut to fit the width of the inner recessed cabinet bottom)
B.Outside top exhaust (Vertical duct–7″ Round)
•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.
Hood mounting screws (4)
133⁄4″ (30″ hood) |
|
|
| 13 | 3 | ″ | (30 | ″ | hood) |
163⁄4″ (36″ hood) |
| ⁄4 |
| ||||||
16 | 3 | ″ | (36 | ″ | hood) | ||||
|
| ⁄4 |
| ||||||
Cabinet front
Cabinet |
| 73⁄4″ |
|
|
| |
bottom | 8″ DIA. |
| 9 | 5 | ⁄8″ | |
Access | 11⁄4″ | |||||
HOLE |
| |||||
hole for 7″ |
| 53⁄4″ |
|
|
| |
round duct |
| 13⁄8″ |
|
| ||
|
|
|
| |||
|
|
|
|
|
Wood shims |
| Electrical access | |
Center | hole (in cabinet bottom) | ||
line |
| ||
| |||
of 3/8″ thick and cut to fit the |
|
| |
width of the inner recessed |
|
| |
cabinet bottom) |
|
|
C. Outside rear exhaust
(Horizontal duct–31⁄4″ x 10″ Rectangular)
•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.
Wood shims
| Cabinet front | 1⁄2″ 11⁄4″ | |
33⁄4″ | Horizontal duct |
| |
Cabinet | access hole |
|
|
51⁄4″ | 51⁄4″ |
| |
bottom |
| ||
133⁄4″ (30″ hood) |
| 73⁄4″ |
|
| 133⁄4″ (30″ hood) | ||
163⁄4″ (36″ hood) |
| 163⁄4″ (36″ hood) | |
Hood mounting screws (4) Center line | Electrical access hole |
(in wall) | |
|
|
D. Recirculating
•Use the hood as a template and mark the locations on the cabinet for the electrical wiring and keyhole screw slots.
•Since the hood is to be recirculated (not to be vented outside), do not cut out any vent openings in the wall or cabinet bottom.
12CUT HOLES
Cut holes at marked locations for duct and electrical wiring. For the vertical duct, cut out 3/4″ extra toward the front of the cabinet so you can move the duct freely when installing the hood. It may also ease installation by cutting the hole 101⁄2″ instead of 10″.
13RUN WIRES
Run the electrical wires through the wall or cabinet according to National Electrical Code and applicable local codes.
NOTE: DO NOT turn the power on until installation is complete.
12