Russound Contractor Series manual AT the Amplifier END, Listening Test, Final Assembly

Page 5

AT THE AMPLIFIER END

1.Cut off excess wire, leaving enough to comfortably reach from the hole in the wall to your stereo system. If there’s a possibility that you’re going to move the amplifier to another part of the room, con- sider leaving some excess wire coiled up. If you’ve used sufficiently thick wire, this extra length will not affect speaker performance and could make re-routing easier if the room is rearranged later.

2.Pull the conductors on both speaker wires apart so they’re separated for the last two inches.

3.Using wire strippers, diagonal pliers or a knife, remove 1/2 inch of insulation from each conductor.

4.Twist the tiny strands in each conductor into tight spirals.

5.Attach the speaker wires to the red and black speaker terminals on the amplifier or receiver.

*Connect the POSITIVE (+) conductor to the RED terminal and the NEGATIVE (-) conductor to the BLACK speaker terminal of the receiv- er/amplifier. Make sure that no stray strands of wire have gotten detached and are touching the other main wire.

Repeat Steps 1 through 5 for the other speaker.

LISTENING TEST

It’s a good idea to test everything at this point.

1.Turn on your stereo system. Make sure that the VOLUME control is turned down and that the BALANCE control is set to center.

2.Activate a musical source such as FM or CD player.

3.Gently turn up the volume. You should hear music coming out of your new Russound Speakers! (If you don’t, refer to the troubleshoot- ing guide below.)

4.Now rotate the stereo’s BALANCE control all the way to the LEFT. Sound should only come out of your left speaker. If it comes out of the RIGHT speaker, skip to Step 6.

5.Rotate the BALANCE control all the way to the RIGHT. Sound should only come out of the right speaker.

6.If sound comes from the right speaker when the stereo’s balance control is turned to the LEFT, you’ll need to change the connections on the back of the amplifier/receiver.

6a. FIRST TURN OFF THE AMPLIFIER!

Swap the wires attached to the left and right speaker terminals.

FINAL ASSEMBLY

1.If you haven’t done so already during painting, remove the perforat- ed grilles from both Russound speakers. Use the clamp (dog-ear) to push the grille out from the back side.

2.Center the speaker in the cut-out hole and tighten the screws until the clamps are drawn up snugly from behind, clamping the speaker in place. Try to tighten each screw equally but do not over tighten.

3.Insert the Russound speaker grille by gently pressing it into place.

In most installations, the grilles will fit tightly without causing vibration. If any audible vibration does occur, or if your Russound speakers are ceiling mounted, use the pre-cut lengths of special damping/adhesive material.

Figure 8

Final assembly of SP-C503 speaker baffle and grille

A QUICK TROUBLESHOOTING GUIDE

Before returning your Russound speakers for service, it is a good idea to check out these simple remedies first.

No sound from either speaker:

1.Incorrect source selected on receiver or preamplifier.

2.Mute button pressed on receiver.

3.Wrong speaker output selected; many receivers have an “A” and “B” speaker switch. Make sure it’s in the correct position.

4.In-Wall Volume control not turned up or wired incorrectly.

5.If using a “speaker selector,” room/station not turned on or improper- ly connected.

No sound from one speaker:

1.Unsecured connection at either the speaker or amplifier - double-check them.

2.Balance control turned all the way left or right-return it to center.

3.Bad connecting cable between sound source and amplifier - try a new cable.

4.Defective speaker - contact your Russound dealer or call Russound Tech Support at 603.659.5170.

Any other problems not listed, discuss with your dealer or call Russound.

5

Image 5
Contents Built for sound priced for value Where to Place Your Ceiling Speakers Speaker WireIntroduction Other Acoustic ConsiderationsInstallation Speaker Wire PathsCorners and Reflections ListeningHooking UP Your Speakers Identifying + Painting the SpeakersCutting Holes for the Speakers AT the Speaker ENDQuick Troubleshooting Guide Final AssemblyAT the Amplifier END Listening TestTaking Care of Your NEW Ceiling Speakers Installing During NEW ConstructionMore on Speaker Wires and Amplifier Impedance SP-C503 Recommended PowerSP-C522 SP-C622SP-C550 SP-C523SP-C623 SP-C650 WarrantyPage Page Forbes Rd. Newmarket, NH 03857, USA Fax Fax-On-Demand

Contractor Series specifications

Russound Contractor Series offers a range of high-quality audio solutions designed to deliver exceptional performance in residential and commercial installations. Known for their reliability and versatility, these systems are ideal for a variety of applications, from whole-house audio to multi-zone setups.

One of the standout features of the Russound Contractor Series is its scalability. The systems can be easily expanded to accommodate growing needs, making them suitable for both small homes and large commercial spaces. This flexibility ensures that users can enjoy high-quality sound in every room without the need for complex reconfigurations.

The Contractor Series incorporates advanced technologies that enhance audio performance. For instance, the systems are designed with high-efficiency amplifiers, which deliver powerful sound while minimizing power consumption. This is particularly beneficial in commercial environments where energy usage can significantly impact operating costs. Additionally, the use of premium components ensures that audio quality remains uncompromised, with clear highs and robust bass.

Zone control is another important characteristic of the Contractor Series. Users can manage multiple audio zones independently, allowing them to enjoy different music in different spaces simultaneously. This feature is particularly useful in homes with open concepts or businesses that host events in multiple areas. The intuitive control options include keypads, mobile apps, and touch panels, providing users with convenience and ease of access.

Russound also emphasizes user-friendly installation with the Contractor Series. The systems are designed for straightforward setup, featuring modular designs that facilitate seamless integration with other components. This allows installers to save time and effort, ultimately reducing labor costs. Furthermore, the series supports a variety of audio sources, including streaming services, local libraries, and traditional radio, ensuring that users have access to an extensive range of content.

In summary, the Russound Contractor Series stands out in the market due to its high-quality audio performance, scalable design, advanced technology, and user-friendly installation features. Ideal for both residential and commercial applications, this series offers versatile solutions that meet the diverse needs of modern audio environments. Whether for enhancing home entertainment or creating a rich sound experience in commercial spaces, the Contractor Series provides reliable and impressive audio solutions that listeners can appreciate.