GE PVM2070 warranty A4. Mount the Microwave Oven, A3. Check for Proper Damper Operation

Page 13
Damper
Back of
Microwave
• Place the microwave in its upright position, with the top of the unit facing up.
• This microwave oven may be shipped assembled for top exhaust (adaptor installed) or for recirculation exhaust (adaptor absent).
• Make sure tape securing damper is removed and damper pivots easily before mounting microwave.
• You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

Installation Instructions

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

•Read the instructions on the TOP CABINET TEMPLATE.

•Tape it underneath the top cabinet.

•Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

A4. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from overtightening screws.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

A3. CHECK FOR PROPER DAMPER OPERATION

 

Exhaust Adaptor

Blower Plate

(absent on models shipped

for recirculation exhaust)

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

2Rotate front of oven up against cabinet bottom.

1

Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

3Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Read Carefully Keep These Instructions Before YOU BeginContents Installation InstructionsElectrical Requirements Important Safety InstructionsOutside TOP Exhaust Example only Hood ExhaustOutside Back Exhaust Example only Maximum duct length Exhaust connectionParts Included Damage SHIPMENT/ InstallationHardware Packet Additional PartsMounting Space Tools YOU will NeedFinding the Wall Studs Placement of the Mounting PlateMicrowave Must be Level Determining Wall Plate Location Under Your CabinetSet the mounting plate aside Aligning the Wall PlateSee Recirculating NON-VENTED DuctlessA1. Attach the Mounting Plate to the Wall Installation OverviewTo use toggle bolts A2. USE TOP Cabinet Template for Preparation of TOP Cabinet A4. Mount the Microwave OvenA3. Check for Proper Damper Operation A6. Connecting Ductwork A5. Adjust the Exhaust AdaptorA4. Mount the Microwave Oven B1. Preparing the Rear Wall for Outside Back Exhaust B2. Remove Exhaust AdaptorB5. Adapting Microwave Blower for Outside Back Exhaust B3. Attach the Mounting Plate to the WallB4. USE TOP Cabinet Template for Preparation of TOP Cabinet B5. Adapting Microwave Blower for Outside Back Exhaust B6. Mount the Microwave Oven C2. USE TOP Cabinet Template for Preparation of TOP Cabinet C1. Attach the Mounting Plate to the WallRecirculating Non-Vented Ductless C4. Adapting Microwave Blower for Recirculation C3. Check Microwave AssemblyC5. Mount the Microwave Oven C4. Adapting Microwave Blower for RecirculationC5. Mount the Microwave Oven C6. Installing Charcoal FilterBefore YOU USE Your Microwave 49-40569 07-07 JR DE68-03451A LEA Cuidadosamente Guarde Estas Instrucciones Antes DE EmpezarInformación general ContenidoGuía de instalación paso por paso Requisitos Eléctricos Instrucciones DE Seguridad ImportantesEscape Superior Externo Ejemplo Solamente Campana DE EscapeEscape Posterior Externo Ejemplo Solamente Longitud máxima del conducto Conexiones de escapePartes Incluidas Daños Envío InstalaciónPaquete DE Elementos Partes AdicionalesEspacio DE Montaje Herramientas QUE NecesitaráCómo Encontrar LOS Postes DE Viga EN LA Pared Cómo Colocar EL Plato DE MontajeEL Horno Microondas Debe Quedar Nivelado Agujero a Cómo Alinear EL Plato DE Montaje Sobre LA ParedEscape Posterior Exterior Conducto Horizontal Escape Superior Exterior Conducto VerticalRecirculación SIN Conducto DE Ventilación Ver páginaA1. Cómo Adherir LA Placa DE Montaje a LA Pared Perspectiva General DE LA InstalaciónPara usar los tornillos basculantes A4. Cómo Montar EL Horno Microondas A3. Inspeccione LA Operación DEL Regulador DE TiroA6. Cómo Conectar EL Conducto A4. Cómo Montar EL HornoA5. Cómo Ajustar EL Adaptador DE Escape Nota B2. Remueva EL Adaptador DE EscapeB3. Cómo Adherir EL Plato DE Montaje a LA Pared B5. Cómo Adaptar EL CalefactorDEL Microondas Para EL Escape Exterior DEL Microondas Para EL Escape Exterior continuación B6. Cómo Montar EL Horno Microondas C1. Cómo Adherir LA Placa DE Montaje a LA Pared Recirculación Sin conducto de ventilaciónPerspectiva General DE LA Instalación C3. Inspeccione LA Ensambladura DEL Microondas Recirculación continuación DEL Microondas Para LAC5. Cómo Montar EL Horno Microondas C6. Cómo Instalar EL Filtro DE Carbonilla C5. Cómo Montar EL HornoAntes DE Comenzar a Usar SU Horno Microondas 49-40569-S 07-07 JR

PVM2070 specifications

The GE PVM2070 is a compact over-the-range microwave oven that combines functionality with efficiency, making it an asset in any modern kitchen. This model is designed to address the cooking needs of families while maximizing space utilization. With a sleek design and user-friendly interface, the PVM2070 stands out as a preferred choice among consumers.

One of the key features of the GE PVM2070 is its 1.9 cubic feet capacity, which provides ample space for cooking larger dishes without compromising on convenience. This microwave is equipped with 1000 watts of power, ensuring that food heats evenly and efficiently. The unit includes several pre-programmed settings that allow users to quickly reheat leftovers, defrost meat, and cook a variety of popular foods such as popcorn, baked potatoes, and pizza.

Another noteworthy technology integrated into the GE PVM2070 is its Sensor Cooking feature. This innovative technology detects moisture levels in the food, automatically adjusting cooking times and power levels for optimal results. This takes the guesswork out of reheating and cooking, ensuring that meals are perfectly cooked every time.

The PVM2070 is also equipped with an easy-to-use digital control panel, featuring a bright LED display that makes it simple to navigate settings. The panel includes a convenient timer, allowing users to track cooking times accurately. Additionally, the unit comes with a turntable that promotes even cooking by rotating food during the heating process, eliminating cold spots.

In terms of design, the GE PVM2070 features a modern, stainless steel exterior that not only enhances kitchen aesthetics but also offers durability and ease of cleaning. The over-the-range configuration frees up valuable counter space, making it ideal for smaller kitchens. Furthermore, this microwave includes an integrated ventilation system that can function as either a recirculating vent or a ducted vent, effectively eliminating smoke, steam, and odors from the kitchen during cooking.

The safety features of the PVM2070 are also commendable, with a child lock option that prevents accidental operation.

Overall, the GE PVM2070 is a reliable and versatile microwave oven that encapsulates advanced cooking technology, making it an excellent addition to any home.
Top Page Image Contents