GE PVM2070 warranty B6. Mount the Microwave Oven

Page 18

Installation Instructions

B6. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from overtightening screws.

3Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Equivalent to Depth of Cabinet Recess

Self-Aligning Screw

Microwave Oven Top

4Attach the microwave oven to the top cabinet.

5 Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1

Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

6 Tighten center screw completely.

7Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.)

2Rotate front of oven up against cabinet bottom.

8Install grease filters. See the Owner’s Manual packed with the microwave.

18

Image 18

Contents Before YOU Begin Read Carefully Keep These InstructionsInstallation Instructions ContentsImportant Safety Instructions Electrical RequirementsHood Exhaust Outside TOP Exhaust Example onlyOutside Back Exhaust Example only Exhaust connection Maximum duct lengthHardware Packet Damage SHIPMENT/ InstallationParts Included Additional PartsTools YOU will Need Mounting SpacePlacement of the Mounting Plate Finding the Wall StudsDetermining Wall Plate Location Under Your Cabinet Microwave Must be LevelAligning the Wall Plate Set the mounting plate asideRecirculating NON-VENTED Ductless SeeInstallation Overview A1. Attach the Mounting Plate to the WallTo use toggle bolts A4. Mount the Microwave Oven A2. USE TOP Cabinet Template for Preparation of TOP CabinetA3. Check for Proper Damper Operation A5. Adjust the Exhaust Adaptor A6. Connecting DuctworkA4. Mount the Microwave Oven B2. Remove Exhaust Adaptor B1. Preparing the Rear Wall for Outside Back ExhaustB3. Attach the Mounting Plate to the Wall B5. Adapting Microwave Blower for Outside Back ExhaustB4. USE TOP Cabinet Template for Preparation of TOP Cabinet B5. Adapting Microwave Blower for Outside Back Exhaust B6. Mount the Microwave Oven C1. Attach the Mounting Plate to the Wall C2. USE TOP Cabinet Template for Preparation of TOP CabinetRecirculating Non-Vented Ductless C3. Check Microwave Assembly C4. Adapting Microwave Blower for RecirculationC4. Adapting Microwave Blower for Recirculation C5. Mount the Microwave OvenC6. Installing Charcoal Filter C5. Mount the Microwave OvenBefore YOU USE Your Microwave 49-40569 07-07 JR DE68-03451A Antes DE Empezar LEA Cuidadosamente Guarde Estas InstruccionesContenido Información generalGuía de instalación paso por paso Instrucciones DE Seguridad Importantes Requisitos EléctricosCampana DE Escape Escape Superior Externo Ejemplo SolamenteEscape Posterior Externo Ejemplo Solamente Conexiones de escape Longitud máxima del conductoPaquete DE Elementos Daños Envío InstalaciónPartes Incluidas Partes AdicionalesHerramientas QUE Necesitará Espacio DE MontajeCómo Colocar EL Plato DE Montaje Cómo Encontrar LOS Postes DE Viga EN LA ParedEL Horno Microondas Debe Quedar Nivelado Cómo Alinear EL Plato DE Montaje Sobre LA Pared Agujero aRecirculación SIN Conducto DE Ventilación Escape Superior Exterior Conducto VerticalEscape Posterior Exterior Conducto Horizontal Ver páginaPerspectiva General DE LA Instalación A1. Cómo Adherir LA Placa DE Montaje a LA ParedPara usar los tornillos basculantes A3. Inspeccione LA Operación DEL Regulador DE Tiro A4. Cómo Montar EL Horno MicroondasA4. Cómo Montar EL Horno A6. Cómo Conectar EL ConductoA5. Cómo Ajustar EL Adaptador DE Escape B2. Remueva EL Adaptador DE Escape NotaB5. Cómo Adaptar EL Calefactor B3. Cómo Adherir EL Plato DE Montaje a LA ParedDEL Microondas Para EL Escape Exterior DEL Microondas Para EL Escape Exterior continuación B6. Cómo Montar EL Horno Microondas Recirculación Sin conducto de ventilación C1. Cómo Adherir LA Placa DE Montaje a LA ParedPerspectiva General DE LA Instalación C3. Inspeccione LA Ensambladura DEL Microondas DEL Microondas Para LA Recirculación continuaciónC5. Cómo Montar EL Horno Microondas C5. Cómo Montar EL Horno C6. Cómo Instalar EL Filtro DE CarbonillaAntes DE Comenzar a Usar SU Horno Microondas 49-40569-S 07-07 JR