Behringer manual Programming the FCB1010, Selecting Banks and Presets, Rear panel

Page 6

MIDI FOOT CONTROLLER FCB1010

1.3.2 Rear panel

Fig. 1.2: Rear panel connectors

FUSE HOLDER / VOLTAGE SELECTOR. Please make sure that your local voltage matches the voltage indicated on the unit, before you attempt to connect and operate the FCB1010. Blown fuses may only be replaced by fuses of the same type and rating. Some models allow for inserting the fuse holder in two different positions, in order to switch over from 230-V to 120-V operation, and vice versa. Please note that for 120-V operation outside Europe, you need to use a fuse of a higher rating (see chapter 6 “SPECIFICATIONS”).

IEC POWER CONNECTOR. Use the enclosed power cord to connect the unit to the mains.

Use the POWER switch to power up your FCB1010. Always make sure the POWER switch is in its “Off” setting when you connect the FCB1010 to the mains.

+Attention: The POWER switch does not physically disconnect the unit from the mains. Always unplug the unit from the mains when you do not plan on using it for prolonged periods of time.

SERIAL NUMBER. Please take the time to have the warranty card filled out completely, and return it within 14 days after the date of purchase, so as to be entitled to benefit from our extended warranty. Or use our online registration option available on the World Wide Web under www.behringer.com.

Fig. 1.3: Rear panel connectors

SWITCH 1 and 2. Use these jacks to connect your amplifier for channel selection (mono or stereo phone jack cable).

MIDI IN. The MIDI IN of your FCB1010 connects to a sequencer or similar device, in order to download the memory data saved before with the help of the MIDI SysEx function. Additionally, data can be looped through the FCB1010 and merged with other data using the MIDI MERGE function. Subsequently, the combined data are available at the MIDI OUT/THRU connector.

MIDI OUT/THRU. Use this jack to connect the devices you wish to control from your FCB1010. The SOFT THRU circuit allows you to loop through any signals present at the MIDI IN of your FCB1010, merge them with the unit’s own data stream, and finally output the combined data at the MIDI OUT.

2. PROGRAMMING THE FCB1010

In this chapter you will learn to program your FCB1010 and adapt it to your specific MIDI set-up. But don’t worry, you won’t have to learn a programming language before you could give your FCB1010 a single MIDI command. The unit will perform all functions for you, one after the other. Simply make and confirm your choices. If particular functions prompt you to enter a parameter, this will be covered specifically.

2.1 Selecting BANKS and PRESETS

There are two options to select a BANK and the PRESETS it contains. Which one you use depends on the DIRECT SELECT parameter in the GLOBAL CONFIGURATION menu. If DIRECT SELECT is on, you can use the PRESET footswitches to directly select the BANK number followed by the PRESET number. If DIRECT SELECT is off, you need to step through the various BANKS (using the UP/DOWN switches), then select a PRESET from a bank. The default setting is OFF. The illustrations below show the two options.

2.1.1 DIRECT SELECT deactivated

Let’s assume you wish to select PRESET #1 from BANK #3...

Step 1

Use the UP/DOWN switches to go to the BANK that contains the PRESET of your choice (here: BANK #3).

Step 2:

Select the PRESET you wish to use (here: PRESET #1).

Fig. 2.1: PRESET selection with DIRECT SELECT disabled

2.1.2 DIRECT SELECT activated

If DIRECT SELECT is on, do as follows to select PRESET #1 from BANK #3 (activating DIRECT SELECT is discussed in ch. 2.2.1):

Step 1

Select the BANK of your choice (here: BANK #3) by stepping on footswitch #3.

Step 2

Select the PRESET you wish to use (here: PRESET #1) by stepping on footswitch #1. The display shows that preset 31 is selected.

6

2. PROGRAMMING THE FCB1010

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Midi Foot Controller Version 1.4 MarchImportant Safety Instructions Detailed Safety InstructionsMidi Foot Controller Table of Contents ForewordIntroduction Before you get startedUser’s manual Control elements Rear panel Selecting Banks and PresetsProgramming the FCB1010 Direct Select deactivatedTab .1 Footswitches and assigned Midi functions Midi channel settingConfig Direct SelectQuick start guide for Preset programming Setup menuProgramming mode Detailed Preset programming Programming the Note function Tab .4 Assignment of Midi Note numbersData storage Controller toggle functionTAP-TEMPO function Saving the FCB1010 memory with the help of SysEx dumpsCalibrating expression pedals a and B Restoring factory presetsTab .5 Reset key combinations Receiving SysEx dumpsApplications Basic setupExpanded setup using the switch function Connections generalMidi data format MIDI-A STANDARD, a RevolutionMidi connections Control Change messagesSpecifications Running statusTab .1 Midi Implementation Warranty

FCB1010 specifications

The Behringer FCB1010 is a versatile MIDI foot controller designed for musicians and performers to gain seamless control over their effects, amplifiers, and audio devices. This robust device is especially popular among guitarists, keyboardists, and electronic music producers seeking a reliable and easy-to-use MIDI controller.

One of the FCB1010's standout features is its ability to send a variety of MIDI messages, making it compatible with nearly all MIDI-capable devices. It boasts ten programmable footswitches, which can be assigned to control different functions or parameters such as effects on/off, volume control, or even triggering loops. Each footswitch can send multiple MIDI messages simultaneously, allowing for intricate setups and complex live performances.

Additionally, the FCB1010 includes two expression pedals, enabling musicians to manipulate sound parameters in real-time. Users can assign these pedals to control effects such as volume swells, wah effects, and modulation depth, thus enriching their performance with dynamic expression.

The controller is equipped with a bright 7-segment LED display, which shows useful information such as the currently selected preset and MIDI channel. This feature allows for easy navigation across the various patches and settings without needing to consult external devices or documentation mid-performance.

Connectivity is another strong suit of the FCB1010, as it offers a MIDI OUT port that allows the controller to interface with a wide range of equipment, such as synths, drum machines, and DAWs. It also features a dedicated power supply input, ensuring reliable power during extensive use.

The FCB1010 can store up to 100 user-defined presets, giving performers the flexibility to switch between various setups quickly. Performers can also utilize the controller's built-in MIDI merge capability, enabling the connection of additional controllers or instruments into a single MIDI output stream.

Behringer's MIDI foot controller is built with durability in mind, featuring a rugged metal chassis that can withstand the rigors of live performances. Its solid construction ensures that it will endure the challenges of touring and frequent use, making it an ideal choice for both amateur and professional musicians alike.

In summary, the Behringer FCB1010 serves as a powerful tool for integrating MIDI control into live performances and studio setups. With its programmable footswitches, expression pedals, LED display, and robust construction, it is a favored choice for artists looking for reliable performance and flexibility in their creative endeavors.
Top Page Image Contents