Behringer FCB1010 manual Quick start guide for Preset programming, Setup menu, Programming mode

Page 8

MIDI FOOT CONTROLLER FCB1010

 

 

 

￿￿￿￿￿￿

￿￿￿￿￿￿￿￿

 

 

 

￿￿￿￿￿￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

program change commands, two controller commands, two

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Determines if UP key toggles

 

different controller values (using the expression pedals) and a

 

 

 

 

 

 

 

Note On command to the connected equipment at the same time

 

1

 

SWITCH 1

 

SWITCH 1 relay while DIRECT

 

 

 

 

 

(menu structure as in fig. 2.4). It is up to you to determine, which

 

 

 

 

 

 

 

SELECT is enabled.

 

 

 

 

 

 

 

 

 

commands are stored in a PRESET. Do as follows to program the

 

 

 

 

 

 

Determines if DOWN key toggles

 

 

 

 

 

 

 

 

functions to be sent with each PRESET:

 

2

 

SWITCH 2

 

SWITCH 2 relay while DIRECT

 

s Select the PRESET you wish to edit.

 

 

 

 

 

 

 

SELECT is enabled.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

COPY

 

Enables copying presets (see ch.

 

s Press DOWN for more than 2.5 sec to enter PRESET

 

 

PRESET

2.4.1).

 

 

 

programming mode. The number in the display disappears

 

 

 

 

 

 

 

6

 

SYSEX

Sends the entire memory as a sysex

 

 

while the green SWITCH 1/SWITCH2 LED in the display

 

 

 

 

starts flashing.

 

 

 

 

SEND

 

 

 

dump.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When this switch is pressed, the

 

s Use footswitches 1 and 2 to edit the status of the

 

 

 

SYSEX

 

FCB1010 waits for the reception of

 

 

SWITCHES. The current status is indicated by the foot-

 

7

 

system-exclusive data. Switch LED

 

 

switch LED and the corresponding SWITCH LED in the

 

 

RCV

 

 

 

 

 

 

dies out when the data have been

 

 

acrylic display. For further details see chapter 3.3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

received correctly.

 

 

“Connections (general)”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+ Please note that the status of the SWITCHES can

 

 

 

 

 

 

Allows to merge MIDI IN data with

 

 

 

 

 

 

 

FCB1010-generated data. The

 

 

also be toggled with UP (SWITCH 1) and DOWN

 

8

 

MERGE

 

combined data stream is

 

 

(SWITCH 2) if DIRECT SELECT is enabled. The only

 

 

 

 

 

 

subsequently output at the MIDI

 

 

prerequisite is that this function has been enabled

 

 

 

 

 

 

 

 

OUT.

 

 

for both SWITCHES in the CONFIGURATION menu.

 

 

 

 

 

 

 

 

 

 

 

 

s Confirm with UP/ENTER. The SELECT LED in the display

 

 

 

 

 

 

Enables/disables running status

 

 

 

 

 

 

 

 

 

lights up.

 

 

 

 

 

 

 

feature. Serves to make efficient use

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

RUNNING

 

of the MIDI transmission rate. The

 

s Activate individual MIDI functions by keeping the respective

 

 

STATUS

MIDI status byte from the expression

 

 

footswitch depressed for roughly 1.5 sec. Footswitch LEDs

 

 

 

 

 

 

 

 

 

 

 

pedals is sent only if it differs from

 

 

indicate the activated footswitches of the respective MIDI

 

 

 

 

 

 

the preceding status byte.

 

 

functions. As long as the display indicates SELECT, you

 

 

 

 

 

 

 

 

 

 

 

 

 

can activate MIDI functions and select them for editing by

Tab. 2.2: Assignment of footswitches in CONFIGURATION

 

briefly pressing the corresponding footswitch. The selected

 

footswitch LED and the display blink during selection and

 

 

 

 

 

 

setup menu

 

 

 

 

 

 

 

 

activation. The NUMBER LED is also lit. The following MIDI

+ External equipment, for example guitar or bass

 

 

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿functions are available for selection:￿￿￿￿￿￿

 

amps, can be controlled by using SWITCH 1 and 2

 

 

 

 

 

 

 

outputs of the FCB1010. If the FCB1010 triggers this

 

 

 

 

 

 

 

function, you should first check if the piece of

 

1

 

PRG CHG 1

Program change command #1

 

 

equipment you

are trying to control reacts to

 

 

 

 

 

2

 

PRG CHG 2

Program change command #2

 

 

connection state (contact open or closed) or current

 

 

 

 

 

3

 

PRG CHG 3

Program change command #3

 

 

feed (contact closed as long as the switch is

 

 

 

 

depressed). BEHRINGER guitar and bass amps react

 

4

 

PRG CHG 4

Program change command #4

 

 

to current feeds. Therefore, when you wish to

 

 

 

 

 

 

 

 

5

 

PRG CHG 5

Program change command #5

 

 

remotely control channel change on a BEHRINGER

 

 

 

 

 

6

 

CNT 1

Controller 1

 

 

guitar amp not via MIDI but via switch outputs

 

 

 

 

(because you have no MIDI cable at your disposal),

 

7

 

CNT 2

Controller 2

 

 

you have to power off switch 1 & 2 LEDs in GLOBAL

 

8

 

EXP A

Expression Pedal A

 

 

CONFIGURATION menu under CONFIG. These LEDs

 

 

 

 

 

9

 

EXP B

Expression Pedal B

 

 

are on in the default setting and indicate that

 

 

 

 

 

10/0

 

NOTE

Transmits a MIDI note

 

 

programmed connection state is kept.

 

 

 

 

Basically, CONFIGURATION mode functions are active as long

 

 

Tab. 2.3: Footswitch assignment in PRESET

as the corresponding footswitch LED is lit.

 

 

 

programming mode

2.3 Quick start guide for PRESET programming

+ MIDI channel adjustment for the respective MIDI

 

functions is not done during preset programming;

 

 

 

 

 

 

 

 

 

 

 

 

 

it is done in GLOBAL CONFIGURATION on MIDI

 

 

 

 

 

 

 

 

 

 

 

 

 

FUNCTION page (see ch. 2.2.2).

 

 

 

 

 

 

 

 

 

 

 

 

s Confirm your selection with UP/ENTER, in order to start

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

programming the selected MIDI function, or cancel with

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DOWN/ESCAPE. Use footswitches 1 through 10/0 or

 

 

 

 

 

 

 

 

 

 

 

 

 

EXPRESSION PEDAL A to enter the parameter values of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

your choice.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

s If you have selected PROGRAM CHANGE as the MIDI

 

 

 

 

 

 

 

 

 

 

 

 

 

function to be edited, you can now enter a program change

 

 

 

 

 

 

 

 

 

 

 

 

 

number from 1 through 128 and confirm your selection

 

 

 

 

 

 

 

 

 

 

 

 

 

with UP/ENTER.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

s If you have selected CNT1 or CNT2, you can now enter

 

 

 

Fig. 2.4: PRESET programming

 

 

 

 

the number of the controller to be sent (0 through 127)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For each of the 100 PRESETS you can determine which MIDI

 

when you press the corresponding footswitch. After

functions shall be transmitted as soon as you select the

 

confirming your selection with UP/ENTER you can select a

respective PRESET. For instance, you can send five different

 

controller value (0 through 127). Confirm your selection

 

 

 

 

 

 

 

 

 

 

 

 

 

with UP/ENTER.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

2. PROGRAMMING THE FCB1010

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Midi Foot Controller Version 1.4 MarchImportant Safety Instructions Detailed Safety InstructionsMidi Foot Controller Table of Contents ForewordUser’s manual Control elements IntroductionBefore you get started Selecting Banks and Presets Programming the FCB1010Rear panel Direct Select deactivatedMidi channel setting ConfigTab .1 Footswitches and assigned Midi functions Direct SelectProgramming mode Quick start guide for Preset programmingSetup menu Detailed Preset programming Programming the Note function Tab .4 Assignment of Midi Note numbersController toggle function TAP-TEMPO functionData storage Saving the FCB1010 memory with the help of SysEx dumpsRestoring factory presets Tab .5 Reset key combinationsCalibrating expression pedals a and B Receiving SysEx dumpsBasic setup Expanded setup using the switch functionApplications Connections generalMIDI-A STANDARD, a Revolution Midi connectionsMidi data format Control Change messagesTab .1 Midi Implementation SpecificationsRunning status Warranty

FCB1010 specifications

The Behringer FCB1010 is a versatile MIDI foot controller designed for musicians and performers to gain seamless control over their effects, amplifiers, and audio devices. This robust device is especially popular among guitarists, keyboardists, and electronic music producers seeking a reliable and easy-to-use MIDI controller.

One of the FCB1010's standout features is its ability to send a variety of MIDI messages, making it compatible with nearly all MIDI-capable devices. It boasts ten programmable footswitches, which can be assigned to control different functions or parameters such as effects on/off, volume control, or even triggering loops. Each footswitch can send multiple MIDI messages simultaneously, allowing for intricate setups and complex live performances.

Additionally, the FCB1010 includes two expression pedals, enabling musicians to manipulate sound parameters in real-time. Users can assign these pedals to control effects such as volume swells, wah effects, and modulation depth, thus enriching their performance with dynamic expression.

The controller is equipped with a bright 7-segment LED display, which shows useful information such as the currently selected preset and MIDI channel. This feature allows for easy navigation across the various patches and settings without needing to consult external devices or documentation mid-performance.

Connectivity is another strong suit of the FCB1010, as it offers a MIDI OUT port that allows the controller to interface with a wide range of equipment, such as synths, drum machines, and DAWs. It also features a dedicated power supply input, ensuring reliable power during extensive use.

The FCB1010 can store up to 100 user-defined presets, giving performers the flexibility to switch between various setups quickly. Performers can also utilize the controller's built-in MIDI merge capability, enabling the connection of additional controllers or instruments into a single MIDI output stream.

Behringer's MIDI foot controller is built with durability in mind, featuring a rugged metal chassis that can withstand the rigors of live performances. Its solid construction ensures that it will endure the challenges of touring and frequent use, making it an ideal choice for both amateur and professional musicians alike.

In summary, the Behringer FCB1010 serves as a powerful tool for integrating MIDI control into live performances and studio setups. With its programmable footswitches, expression pedals, LED display, and robust construction, it is a favored choice for artists looking for reliable performance and flexibility in their creative endeavors.
Top Page Image Contents