Behringer FCB1010 manual Detailed Preset programming

Page 9

MIDI FOOT CONTROLLER FCB1010

sIf you have selected EXP A or EXP B, you can now enter the controller number the EXPRESSION PEDAL of your choice is aimed to send values for. Confirm your selection with UP/ENTER and enter the lower value (pedal up). Confirm with UP/ENTER.

Afterwards, enter the upper value (pedal pressed down completely) and confirm once again with UP/ENTER.

+Please keep in mind that the first controller value always has to be lower than the second controller value!

+You can quit the programming mode at any time by means of a long press on DOWN. Any confirmed entries will be stored with the currently selected

PRESET.

+How to program the NOTE function is explained in chapter 2.4.6.

2.4Detailed PRESET programming

2.4.1 Preset copy function

The preset copy function copies an already programmed preset to a new preset of your choice. This saves you time, since you do not have to repeat all adjustments for each newly programmed preset.

sActivate CONFIG in the GLOBAL CONFIGURATION (see chapter 2.2).

sNow, press footswitch 5 to activate the copy function. The VALUE 1 LED lights up. The number in the display and the footswitch LED start flashing.

sEnter the number of the preset you wish to copy and confirm your selection with UP/ENTER. The VALUE 2 LED lights up. The number in the display and the footswitch LED start flashing.

+Presets 1 - 10 are stored in bank 0, presets 11 - 20 in bank 1, and so on.

sEnter the target preset and confirm your selection with UP/ ENTER, or cancel with DOWN/ESCAPE.

sIf you want to copy further presets, please press footswitch 5 again. Press and hold DOWN/ESCAPE to quit the GLOBAL CONFIGURATION.

2.4.2Programming switches

sSelect the PRESET you wish to edit.

sPress DOWN for more than 2.5 sec to enter PRESET programming mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing.

sEnable/disable the SWITCHES using footswitches 1 and/or 2 and confirm your selection with UP/ENTER. The corresponding footswitch and SWITCH LEDs light up.

sExit PRESET programming mode through keeping the DOWN/ ESCAPE key for a few seconds, or press the UP/ENTER key in order to get to the next page, where you can edit various MIDI functions for the preset selected at the beginning.

2.4.3Programming program changes

sSelect the PRESET you wish to edit.

sKeep the DOWN/ESCAPE key pressed longer than 2.5 sec. to get to the programming mode. The green SWITCH 1/ SWITCH 2 LED in the display starts flashing.

sUse the UP/ENTER key to get to the next page. The SELECT LED in the display is lit.

+To program a MIDI function, you have to first activate it. Individual MIDI functions are activated by keeping the corresponding keys pressed for a few seconds. Active MIDI functions are indicated by a permanently lit footswitch LED.

sSelect the PROGRAM CHANGE you wish to program for the selected PRESET by briefly pressing the respective footswitch (footswitches 1 to 5). The footswitch LED blinks.

sConfirm your selection by pressing UP/ENTER. The NUMBER LED in the display lights up.

sEnter the program change command (1 bis 128) via the footswitch or expression pedal A.

sConfirm your selection by pressing UP/ENTER or cancel by pressing DOWN/ESCAPE. The SELECT LED in the display lights up.

sSelect an additional MIDI function you wish to edit or exit the PRESET programming mode by keeping the DOWN/ ESCAPE key for a few seconds.

2.4.4Programming CONTROL CHANGES

sSelect the PRESET you wish to edit.

sKeep DOWN pressed for more than 2.5 sec to enter PRESET programming mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing.

sUse the UP/ENTER key to get to the next page. The SELECT LED in the display lights up.

+To program a MIDI function, you have to first activate it. Individual MIDI functions are activated by keeping the corresponding keys pressed for a few seconds. Active MIDI functions are indicated by a permanently lit footswitch LED.

sKeep the corresponding footswitch (foot key 6 or 7) pressed for a few seconds to activate the controller you wish to edit. The controller is selected by pressing the key briefly again. The LED blinks.

sConfirm your selection by pressing UP/ENTER. The NUMBER LED in the display lights up.

sEnter the desired controller number (0 to 127) by using the foot keys or the expression pedal A.

sConfirm your selection with UP/ENTER. The VALUE 1 LED in the display lights up.

sUse the footswitches 1 through 10/0 or EXPRESSION PEDAL A to enter the controller value (0 through 127).

+To correct your selection, use the DOWN/ESCAPE key to go one step backward.

sConfirm your selection by pressing UP/ENTER. The SELECT LED in the display lights up.

sSelect an additional MIDI function you wish to edit or quit the PRESET programming mode by keeping DOWN/ESCAPE pressed for a few seconds.

2.4.5Programming EXPRESSION PEDALS A/B

sSelect the PRESET you wish to edit.

sKeep DOWN pressed for more than 2.5 sec to enter PRESET programming mode. The green SWITCH 1/SWITCH 2 LED in the display starts flashing.

sUse UP/ENTER to get to the next page. The SELECT LED in the display begins to light up.

+To program a MIDI function, you have to first activate it. Individual MIDI functions are activated by keeping the corresponding keys pressed for a few seconds. Active MIDI functions are indicated by a permanently lit footswitch LED.

2. PROGRAMMING THE FCB1010

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Version 1.4 March Midi Foot ControllerDetailed Safety Instructions Important Safety InstructionsMidi Foot Controller Foreword Table of ContentsIntroduction Before you get startedUser’s manual Control elements Programming the FCB1010 Selecting Banks and PresetsRear panel Direct Select deactivatedConfig Midi channel settingTab .1 Footswitches and assigned Midi functions Direct SelectQuick start guide for Preset programming Setup menuProgramming mode Detailed Preset programming Tab .4 Assignment of Midi Note numbers Programming the Note functionTAP-TEMPO function Controller toggle functionData storage Saving the FCB1010 memory with the help of SysEx dumpsTab .5 Reset key combinations Restoring factory presetsCalibrating expression pedals a and B Receiving SysEx dumpsExpanded setup using the switch function Basic setupApplications Connections generalMidi connections MIDI-A STANDARD, a RevolutionMidi data format Control Change messagesSpecifications Running statusTab .1 Midi Implementation Warranty

FCB1010 specifications

The Behringer FCB1010 is a versatile MIDI foot controller designed for musicians and performers to gain seamless control over their effects, amplifiers, and audio devices. This robust device is especially popular among guitarists, keyboardists, and electronic music producers seeking a reliable and easy-to-use MIDI controller.

One of the FCB1010's standout features is its ability to send a variety of MIDI messages, making it compatible with nearly all MIDI-capable devices. It boasts ten programmable footswitches, which can be assigned to control different functions or parameters such as effects on/off, volume control, or even triggering loops. Each footswitch can send multiple MIDI messages simultaneously, allowing for intricate setups and complex live performances.

Additionally, the FCB1010 includes two expression pedals, enabling musicians to manipulate sound parameters in real-time. Users can assign these pedals to control effects such as volume swells, wah effects, and modulation depth, thus enriching their performance with dynamic expression.

The controller is equipped with a bright 7-segment LED display, which shows useful information such as the currently selected preset and MIDI channel. This feature allows for easy navigation across the various patches and settings without needing to consult external devices or documentation mid-performance.

Connectivity is another strong suit of the FCB1010, as it offers a MIDI OUT port that allows the controller to interface with a wide range of equipment, such as synths, drum machines, and DAWs. It also features a dedicated power supply input, ensuring reliable power during extensive use.

The FCB1010 can store up to 100 user-defined presets, giving performers the flexibility to switch between various setups quickly. Performers can also utilize the controller's built-in MIDI merge capability, enabling the connection of additional controllers or instruments into a single MIDI output stream.

Behringer's MIDI foot controller is built with durability in mind, featuring a rugged metal chassis that can withstand the rigors of live performances. Its solid construction ensures that it will endure the challenges of touring and frequent use, making it an ideal choice for both amateur and professional musicians alike.

In summary, the Behringer FCB1010 serves as a powerful tool for integrating MIDI control into live performances and studio setups. With its programmable footswitches, expression pedals, LED display, and robust construction, it is a favored choice for artists looking for reliable performance and flexibility in their creative endeavors.
Top Page Image Contents