GE JTP20 Securing the Oven in the Opening, C1 Sliding the Oven Into the Opening

Page 10

Installation Instructions

C

Securing the Oven in the Opening

C1 Sliding the Oven Into the Opening

a. Loop (do not tie) a 36string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven.

Pull out on string loop while pushing the oven into the cabinet

b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against oven front frame. Do not push against outside edges.

c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop.

d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening. Remove the string by pulling on one end of the loop.

C2 Drilling the Pilot Holes and Mounting the Oven

NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.

a. Drill through the mounting holes (top and bottom) of the side trim, for the #8 screws provided.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The screws must

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting

 

 

be a minimum of

 

 

 

 

 

Hole

 

 

 

 

 

 

 

 

 

1/4from the front

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Locations

 

 

 

 

 

 

 

 

of the cutout.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: Mounting

screws must be used. Failure to do so could result in the oven

falling out of the cabinet causing serious injury.

b. Secure the oven to cabinet with screws provided.

NOTE: If the cabinet is particle board, you must use #8 x 3/4particle board screws. These may be purchased at any hardware store.

10

(Continued on following page)

Image 10
Contents Installation Installation Instructions Pre-Installation Checklist Do not Lift the Door By the HandleInstallation Instructions Cutout for Single Built-In Oven Cutout for Double Built-In Oven Cutout for Single Built-In Oven Under Counter 240V / 208V Junction Box LocationElectrical Connections Conduit 48 1/2 LongB3 New Construction Four-Conductor Branch Circuit Connection Securing the Oven in the Opening C1 Sliding the Oven Into the OpeningC3 Preparing for the Bottom Trim Installation Replacing the Oven Door Operation Checklist Pre-Test ChecklistPage