GE SCB 1000, ZSC 1001, ZSC 1000, SCB 1001 Oven Removal / Partial Removal, Access Cover, Outer Cover

Page 23

Oven Removal / Partial Removal

To remove the oven from cabinet or wall opening:

WARNING: This oven requires 2 people for complete oven removal. Grasp the bottom of the oven at the front and rear on each side.

Caution: Do not use the oven handle to lift or lower the oven. Damage will occur.

1.Open the door and remove the wire rack, aluminum baking sheet, glass tray, metal tray, and turntable.

2.Remove 4 screws from the side trims

3.Slide the oven forward approximately 11 inches to access some components, or remove it completely from the cabinet or wall opening.

Access Cover

To remove the access cover, the oven must be at least partially removed from the installation.

The access cover is attached to the outer cover by 2 Phillips-head screws.

Outer Cover

To remove the outer cover, the oven must be removed from the installation.

The outer cover is held in place by 21 Phillips-head screws.

4.Unplug the power cord, and lower the oven onto a protected surface.

– 23 –

Image 23

Contents Technical Service Guide Important Safety Notice Page Table of Contents Serial Number NomenclatureB 1 0 0 0 D B B Model NumberIntroduction Features and BeneﬁtsUpper Halogen Lamp/Ceramic Heater SPEEDCOOK/Repeat Last Control FeaturesCooking Times Microwave Speed Cook SystemHalogen Lamp and Ceramic Heaters Rear Convection Heat ElementMicrowave Energy Speedcook Power LevelsUpper Heaters Lower HeaterThermal Compensation Voltage Compensation ChartThermal Compensation Chart Initial Cavity Thermal ProtectionUpper Heater Speedcook Power Level ChartElectrical Requirements InstallationSingle Advantium 120 Installation Advance PlanningMain Component Locator View Component Locator ViewsFront View Bottom View Top ViewRight Side View Left Side ViewControl Panel Assembly Shown separated Control Boards and Panel Connections Power BoardControl Board Relay BoardControl Panel Display BoardSelector Board Components Component Access ChartOuter Cover Access CoverOven Removal / Partial Removal To disassemble the door Door AssemblyDoor-Removal Position Door RemovalTo remove the control panel assembly Control Panel AssemblyTo remove the relay board To remove the power boardTo remove the display board To remove the control panel bracketTo remove the control board Resistance Check Low Voltage TransformerTo remove the selector board To remove the control panelCavity Light Fuse Capacitor and Diode Noise FilterMagnetron TCO Magnetron and Magnetron TCOHigh Voltage Transformer Blower Assembly Damper AssemblyUpper Heater and Oven Cavity TCOs To remove the upper heater assembly Upper Heater AssemblyThermistor Lower Heater AssemblyConvection Heater Assembly and Thermistor To remove the lower heater assemblyConvection Fan Motor Convection Heater ElementHumidity Sensor Test Humidity Sensor Turntable MotorHow to Test Interlock System Left and Right Door Switch AssembliesHow to Test Primary Interlock and Door Sensing Switches How to Test the Monitor SwitchTo replace the door switches Rotate SwitchHow to Adjust the Interlocks To replace the latch boards Diagnostics and Service Information Display Failure Detected Demo ModeFault Codes Standard Test LoadMicrowave Leak Test Proof FeatureSchematics and Wiring Diagrams PCB For The Period GE Will Replace Warranty

SCB 1000, SCB 1001, ZSC 1000, ZSC 1001 specifications

The GE ZSC 1001, ZSC 1000, SCB 1001, and SCB 1000 are cutting-edge solutions in the realm of electrical substations, designed to enhance efficiency, reliability, and safety in power management systems. These devices are integral for utilities seeking to modernize their infrastructures while maintaining optimal performance.

The GE ZSC 1000 series includes both the ZSC 1000 and ZSC 1001 models. These digital relays are renowned for their sophisticated protection and control capabilities. One of the standout features of the ZSC 1001 is its enhanced communication technology, enabling seamless integration with various systems and allowing for real-time data exchange. This model offers advanced protection functions, including overcurrent, distance, and differential protection, which are essential for safeguarding electrical assets.

The ZSC 1000 series is built on a modular architecture, facilitating easy upgrades and customization to meet specific operational needs. It employs intelligent data analysis to help operators predict equipment failures before they happen, ultimately minimizing downtime and maintenance costs. Additionally, the devices boast user-friendly interfaces that simplify monitoring and control tasks.

The SCB 1000 and SCB 1001 are also key players in GE's portfolio, tailored for busbar protection and automation. These models feature high-accuracy current sensing technology and extensive programmable parameters to suit diverse applications. Their design allows for robust performance in harsh environments, making them ideal for substations.

Both SCB models utilize advanced digital signal processing (DSP) technologies, which enhance their performance and improve the reliability of measurements. The SCB 1001 takes a step further by incorporating security measures to protect against cyber threats, ensuring the integrity of data within the grid.

In terms of interoperability, all four models support various communication protocols, facilitating better connectivity and integration with existing infrastructure. They are designed to operate seamlessly in conjunction with SCADA systems, enabling comprehensive monitoring and control functions.

To summarize, the GE ZSC 1001, ZSC 1000, SCB 1001, and SCB 1000 exemplify modern innovations in electrical protection and control. They offer a blend of advanced technologies, modular designs, and robust performance characteristics, making them invaluable assets for any utility looking to enhance its power management systems. These devices not only meet the current demands of the energy sector but are also equipped to adapt to future challenges in the evolving landscape of electrical distribution and management.