GE SCB 1000, ZSC 1001 Rotate Switch, How to Adjust the Interlocks, To replace the door switches

Page 39

5.Test Circuit Operation.

a.Connect temporary jumper leads across relay contacts, primary interlock and door sensing switches to simulate shorted switch contacts. Locate convenient connections in circuit to be certain COM and NO terminals are used.

b.Connect ohmmeter (Rx1) across the line terminals of the appliance cord. Continuity must show the following:

•Door Closed : Some Ω

•Door Open : .3 Ω

c.Remove 20 amp fuse. Circuit must open (infinity Ω). If not, check wiring of monitor and interlock circuits.

WARNING: After test, remove temporary jumper leads from interlock and relay.

WARNING: Primary interlock, door sensing switch, monitor switch, and relay board must be replaced when the 20 amp fuse is blown due to operation of monitor switch.

Note: Perform microwave leakage test when replacing or adjusting interlock switches or latch board.

How to Adjust the Interlocks:

The latch board is adjustable for proper door closure and switch operation.

1.Disconnect power and partially remove the oven from it’s installation. (See Oven Removal / Partial Removal.)

Note: Each latch board is held in place and adjusted with 2 Phillips-head screws. The screws are recessed from the top of the outer cover. Access holes are provided.

2.Loosen the 2 Phillips-head screws that attach the latch board to the oven chassis.

3.Adjust each latch-board for proper door closure and switch operation, retighten screws.

Note: Perform microwave leakage test when replacing or adjusting interlock switches or latch boards.

To replace the door switches:

1.Place the oven in a partially removed position. (See Oven Removal / Partial Removal.)

2.Open the oven door.

3.Remove the single Phillips-head screw that holds the door switch access cover to the outer cover.

4.Disconnect the switch wiring.

5.Using a flat blade screwdriver, carefully press the lock tab until flush with the surrounding area of the latch board.

6.Using the mounting pin as a pivot, carefully rotate the switch past the lock tab and Remove the switch from the mounting pin.

Rotate Switch

Pivot Pin

Lock Tab

(Continued Next Page)

– 39 –

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Technical Service Guide Important Safety Notice Page Table of Contents Serial Number NomenclatureB 1 0 0 0 D B B Model NumberIntroduction Features and BenefitsUpper Halogen Lamp/Ceramic Heater SPEEDCOOK/Repeat Last Control FeaturesCooking Times Microwave Speed Cook SystemHalogen Lamp and Ceramic Heaters Rear Convection Heat ElementMicrowave Energy Speedcook Power LevelsUpper Heaters Lower HeaterThermal Compensation Voltage Compensation ChartThermal Compensation Chart Initial Cavity Thermal ProtectionUpper Heater Speedcook Power Level ChartElectrical Requirements InstallationSingle Advantium 120 Installation Advance PlanningComponent Locator Views Front ViewMain Component Locator View Bottom View Top ViewRight Side View Left Side ViewControl Panel Assembly Shown separated Control Boards and Panel Connections Power BoardControl Board Relay BoardDisplay Board Selector BoardControl Panel Components Component Access ChartAccess Cover Oven Removal / Partial RemovalOuter Cover To disassemble the door Door AssemblyDoor-Removal Position Door RemovalTo remove the control panel assembly Control Panel AssemblyTo remove the relay board To remove the power boardTo remove the control panel bracket To remove the control boardTo remove the display board Resistance Check Low Voltage TransformerTo remove the selector board To remove the control panelCavity Light Fuse Capacitor and Diode Noise FilterMagnetron and Magnetron TCO High Voltage TransformerMagnetron TCO Blower Assembly Damper AssemblyUpper Heater and Oven Cavity TCOs To remove the upper heater assembly Upper Heater AssemblyThermistor Lower Heater AssemblyConvection Heater Assembly and Thermistor To remove the lower heater assemblyConvection Fan Motor Convection Heater ElementHumidity Sensor Test Humidity Sensor Turntable MotorHow to Test Interlock System Left and Right Door Switch AssembliesHow to Test Primary Interlock and Door Sensing Switches How to Test the Monitor SwitchRotate Switch How to Adjust the InterlocksTo replace the door switches To replace the latch boards Diagnostics and Service Information Display Failure Detected Demo ModeFault Codes Standard Test LoadMicrowave Leak Test Proof FeatureSchematics and Wiring Diagrams PCB For The Period GE Will Replace Warranty

SCB 1000, SCB 1001, ZSC 1000, ZSC 1001 specifications

The GE ZSC 1001, ZSC 1000, SCB 1001, and SCB 1000 are cutting-edge solutions in the realm of electrical substations, designed to enhance efficiency, reliability, and safety in power management systems. These devices are integral for utilities seeking to modernize their infrastructures while maintaining optimal performance.

The GE ZSC 1000 series includes both the ZSC 1000 and ZSC 1001 models. These digital relays are renowned for their sophisticated protection and control capabilities. One of the standout features of the ZSC 1001 is its enhanced communication technology, enabling seamless integration with various systems and allowing for real-time data exchange. This model offers advanced protection functions, including overcurrent, distance, and differential protection, which are essential for safeguarding electrical assets.

The ZSC 1000 series is built on a modular architecture, facilitating easy upgrades and customization to meet specific operational needs. It employs intelligent data analysis to help operators predict equipment failures before they happen, ultimately minimizing downtime and maintenance costs. Additionally, the devices boast user-friendly interfaces that simplify monitoring and control tasks.

The SCB 1000 and SCB 1001 are also key players in GE's portfolio, tailored for busbar protection and automation. These models feature high-accuracy current sensing technology and extensive programmable parameters to suit diverse applications. Their design allows for robust performance in harsh environments, making them ideal for substations.

Both SCB models utilize advanced digital signal processing (DSP) technologies, which enhance their performance and improve the reliability of measurements. The SCB 1001 takes a step further by incorporating security measures to protect against cyber threats, ensuring the integrity of data within the grid.

In terms of interoperability, all four models support various communication protocols, facilitating better connectivity and integration with existing infrastructure. They are designed to operate seamlessly in conjunction with SCADA systems, enabling comprehensive monitoring and control functions.

To summarize, the GE ZSC 1001, ZSC 1000, SCB 1001, and SCB 1000 exemplify modern innovations in electrical protection and control. They offer a blend of advanced technologies, modular designs, and robust performance characteristics, making them invaluable assets for any utility looking to enhance its power management systems. These devices not only meet the current demands of the energy sector but are also equipped to adapt to future challenges in the evolving landscape of electrical distribution and management.
Top Page Image Contents